All rights reserved. 13 NOTE: Make sure all the equipment in the system is turned off when making or breaking connections to the input RCA’s or speaker terminals. Turn on the system and slowly turn up the volume control only after double checking all wire connections. Power for systems with a single amplifier can be supplied by most automotive electrical systems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly reco

(70 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR2504 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum power capability of 250 Watts into two 4. bridged loads l XTR5004 -80 Watts at 4. (125 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR5004 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum

All rights reserved. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz Up to 6 dB of boost is capable at this frequency With +6dB of boost, the woofer has more output down to 23 Hz the overall usable output is increased Figure 8 Figura 8 Abbildung 8 Figure 9 Figura 9 Abbildung 9 AMPLIFIeR WIRInG Power Connections • Power connections accept up to 4 AWG wire • 4 AWG power and ground wire recommended for optimal performance • Connect 12V+ to the battery

AmplifierMODELXTR2502XTR5002OWNER'S MANUAL AmplifierMODELXTR2502XTR5002OWNER'S MANUAL Contents english 1 Francais 19 espanol 35 Deutsch 51 Italiano 67 Portugues 83 Introduction 2 What’s in the Box 2 Practice safe sound™ 2 end Panel Layouts 3 CeA specifications 4 specifications 5 Amplifier settings 6 signal Input and output Configurations 6 Input Gain 6 Line output Configurations 6 Internal Crossover Configurations, Flat (full range) 6 Crossover switch 6 Low-Pass Crossover 6 High-Pass Crossover 7

© 2005 Directed Electronics, Inc. all rights reserved PARALLEL SYNCED GAIN CONNECTIONS/SETTINGS Refer to figure 5 for wiring details. 1. I IIn nnp ppu uut tt S SSi iig ggn nna aal ll - Connect these RCA jacks as described in the Front Panel Connectionsection of this guide. 2. S SSl lla aav vve ee/ //M MMa aas sst tte eer rr S SSw wwi iit ttc cch hh • Set the slave/master switch on the master amplifier to the MASTER position. • Set the slave/master switch on the slave amplifier to the SLAVE posit

8. T TTo oop pp L LLi iig ggh hht tt O OOp ppt tti iio oon nns ss - -i. Light On W/Service Code ii. Light Off W/O Service Code iii. Light On, W/O Service Code iv. Light Off, W/Service Code Default is Light On, W/O Service Code The amplifier contains the ability to control the lights on top of the unit behind the logo badge. In addition to custom tailoring many other features, your Directed Dealer can use a Bitwriter® (V2.0 or later) to setup the top light so that it is either on or off when the

3. S SSi iig ggn nna aal ll C CCo oon nnn nne eec cct tti iio oon nn - Connect an RCA cable between the BRIDGE OUT jack of the 1100d5 and the SLAVE IN jack of the slaved 600d as shown in Figure 6. 4. S SSl lla aav vve ee/ //M MMa aas sst tte eer rr S SSw wwi iit ttc cch hh - Set the slave/master switch of the 600d to the slave position. This will put the I/O RCA jack in the SLAVE IN mode so it will accept the audio signal from the 1100d5’s sync out RCA jack. N NNO OOT TTE EE: ::There is only one

installed by an authorized Directed Directed Audio power amplifiers dealer. If not installed by an authorized continue to set new standards of perfor-dealer, Directed Audio power amplifiers mance, reliability, and affordability in are covered by a one-year, parts-andthe mobile electronics industry. labor limited warranty. Featuring high-efficiency MOSFET power Be sure to retain your original sales supplies, flexible on-board crossovers, receipt and refer to the warranty section and state of the

• The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain se

10. Due to the high-frequency MOSFET switching power supply, filtering the power cable is not generally required (remember that the amp can’t deliver full output if the power supply is restricted). Proper grounding of the signal source is mandatory for the amplifier to reach its performance peak. If the RCA inputs are not grounded adequately via the signal source, electrical noise from the vehicle may be picked up in the system. © 2004 Directed Electronics, Inc FRONT PANEL CONNECTIONS/CONTROLS A