theDawnofaNewAgeinRoboticPoolCleaning! 2008CATALOGSMARTPOOLFeaturingNITRO™... theDawnofaNewAgeinRoboticPoolCleaning! 08NEWFOR08NEWFOR POOL CLEANERS ROBOTIC POOL CLEANER NITRO™RoboticPoolCleanerforIngroundPools#NC31 What Makes NITRO Better Than Any Other Robotic Cleaner? NITROhassomanytechnologicaladvancementsthatmorepatentshavebeenwrittenforitthanonALLroboticpoolcleanerscombinedoverthelast20years!Cleansanytypeofpool-vinylliner,concrete,fiberglass! NEWTECHNOLOGY TWICE THE FILTER AREA NITRO’s extr

When the spa is in use considerable amounts of moisture will escape potentially causing mold and mildew. This can cause health risk. Over time, this can damage certain surfaces, surroundings, and equipment. 4.1 Outdoor Location In selecting the ideal outdoor location for your spa, we suggest that you take into consideration: • The proximity to changing area and shelter (especially in colder weather). • The pathway to and from your spa (this should be free of debris so that dirt and leaves a

Massage Selector (4) • Massage selector 4 controls pump 1 output to footwell IX Jet. Jets Without Massage Selector Controls (5) • Jets 5 are always on when jets pump 2 is running. Page 29 -400 Series 10.14 J-480 Air Controls Diagram Air Controls Operation • Rotate air controls 1-4 to add air to designated jet groups. • Center footwell IX Jet draws air at all times when jets pump 1 is running. This jet has no air control. Page 30 J-400 Serie 10.15 J-470 Massage/Waterfall Selector Diag

a ADDENDUM Jacuzzi J-400 Series Owners Manual, #2530-442U Your new hot tub includes one of two stereo remote styles. Both remotes function 100% identically and contain only minor cosmetic differences outlined below: Style A Style B Cosmetic Differences Between Remotes 1. The hand held remote provides you the ability to select the light system color mode. Remote Style A includes a light "MODE” Button. Remote Style B replaces this button with an "AIR” button that is illustrated by three rows

Contact your dealer or service organization. Note: This message can also appear if the pump has not regained prime after the spa has been drained and refilled. If you suspect that this is the case, see the instructions on page 53 under “pump does not operate but icon does. Ui jrtT lUt Circuit board temperature has exceeded acceptable limit. This message will disappear when the circuit board temperature drops below acceptable limit. If condition persists, provide shade for equipment side of

This manual supplies information for the installation, operation, and servicing of the appliance. READ AND REVIEW THIS MANUAL COMPLETELY before proceeding with an installation. Its use will reduce service calls and chance of injury and will lengthen product life. If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Call (800) 831-7133 for additional free copies of these instructions. FOR YOUR SAFETY Do

3. Test the operation of the pressure relief valve by lifting the valve lever. 4. Test for proper operation of the pressure switch. (See “SWITCH SETTINGS” for testing instructions). 5. On enclosed installations with high-temperature Special Gas Vent systems, repeat the “Final Installation Check,” page 15. Check for evidence of joint leakage. Make sure that joints have not slipped partially or completely apart. Check pipe and fittings for cracks or breaks. The combustion air blower is permanently

To override the time delay, push the Max. Temp. Set Point button again. D. Press the ^ ^^ TEMP or Ў ЎЎ TEMP button on the control panel and set maximum spa temperature to 104°F (40°C) or less. E. Wait up to 30 seconds; the SPA ON light will go off and the unit will shut down. To override the time delay, push the Max. Temp. Set Point button again. 4. Reinstall the access door panels. Initial Troubleshooting Only qualified, trained service technicians with appropriate test equipment should service

Use a Listed roof flashing, roof jack, or roof thimble for all roof penetrations. Do not fill the space around the vent (that is, the clear air space in the thimble or firestop) with insulation. The roof opening must be located so that the vent is vertical. 6. Vent Termination – Vertical (See Figures 12A and 12B, page 13, for height of vent termination above the roof. See Table 7, Page 15, for Listed terminations.) Use a Listed vent terminal specified by local and national codes and your manufac

to 5 P.M.) Phone: (800) 831-7133 Moorpark, California (8 A.M. to 5 P.M.) Phone: (800) 831-7133 (Ext. 6312) Fax: (800) 284-4151 Web sites: visit and © 2005 Pentair Water Pool and Spa, Inc. All rights reserved This document is subject to change without notice 1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000 10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000 Trademarks and disclaimers: IntelliFlo, IntelliTouch and the Pentair Water Pool and Spa logo are trademarks of Pentair Wate