Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop, shake or strike battery. 9. Do not charge inside a box or container of any kind. The battery must be placed in a well ventilated area during charging. ADDITIONAL SAFETY RULES FOR CHAIN SAW 1. Don’t expose chain saw to rain. Don’t use it in damp or wet locations. 2. Hold the chain saw firmly with both hands when the motor is running. 3. Install saw chain properly according to this instruction manual. 4. Do not overreach. Keep proper footing and balance at all times. 5. Keep all parts of the body away from the saw chain when the motor is operating. 6. Before you start the saw, make sure the saw chain is not contacting anything. 7. Switch off the chain saw immediately if you notice anything abnormal in operation. 8. Carefully inspect the chain saw if you drop or strike it against something hard. 9. When not in use, chain saws should be stored in a dry, and high or locked-up place — out of reach of children. When storing saw, use a scabbard (chain cover). 10. Use safety glasses. Also use safety footwear; snug fitting clothing; protective gloves; and head protection. Charging (Fig. 2) 11. Before making a cut, remove dirt, stones, loose bark, nails, staples and wire from the tree. 12. Secure the workpiece so that it will not move suddenly during operation. Be careful of cut-off pieces. They may hit operator. 13. To prevent the saw chain from being pinched in the cut, support the workpiece near the cut using blocks or the like. SAVE THESE INSTRUCTIONS. OPERATING INSTRUCTIONS Installing or removing battery cartridge (Fig. 1) • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Plug the battery charger into the proper AC voltage source. The charging light will flash in green color. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging light will remain lit steadily during charging. When charging is completed in approx. 45 minutes, the charging light color will change from red to green. After charging, unplug the charger from the power source. Battery type Capacity (Ah) Number of cells AP-123 2.0 10 CAUTION: • The battery charger is for charging Dolmar battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • If you charge a battery cartridge from a just-operated tool or battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the battery cartridge from the battery charger. • If the charging light flashes alternately in green and red color, a problem exists and charging is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged. Installing or removing saw chain Installing or removing saw chain • Always be sure that the tool is switched off and the battery cartridge is removed ...