Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Even a non-moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain. Long-term storage Empty the fuel/oil tanks in a well ventilated area. Store the fuel in approved cans in a safe place. Fit the bar guard. Clean the machine. See instructions under the heading Maintenance schedule. Starting and stopping WARNING! Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries. Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything. Keep people and animals well away from the working area. Cold engine Starting: The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards. Ignition; choke: Set the choke control in the choke position. This should automatically set the stop switch to the start position. Start throttle: The correct choke/start throttle setting is obtained by moving the control to the choke position. Air purge: If the machine is fitted with an air purge (A): Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Decompression valve: If the machine is fitted with a decompression valve (B): Press the valve to reduce the pressure in the cylinder and make starting easier. You should always use the decompression valve when starting the machine. Once the machine has started the valve will automatically return to its original setting. BA Warm engine Use the same procedure as for starting a cold engine but without setting the choke control in the choke position. The correct choke/start throttle setting is obtained by moving the choke control to the choke position and then pushing it in again. Starting Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly. Never wrap the starter cord around your hand CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Push in the choke control as soon as the engine fires and make repeated starting attempts. Immediately press and release the throttle when the engine starts. That will disengage the throttle latch. As the chain brake is still activated the engine must return to idling speed as soon as possible by disengaging the throttle latch in order to avoid unnecessery wear on the clutch assembly. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is ready for use. WARNING! Long term inhalation of the engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a health risk. •Never start a chain saw unless the bar, chain and all covers are fitted correctly. See instructions under the heading Assembly. Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injury. •The chain brake should be activated when starting. Se instructions under the heading Start and stop. Do not drop start. This method is very dangerous because you may lose control of the saw. •Never start the machine indoors. Exhaust fumes can be dangerous if inhaled. •Observe your surroundings and make sure that there is no risk of people or animals coming into contact with the cutting equipment. •Always hold the saw with both hands. The right hand should be on the rear handle, and the left hand on the front handle. All people, whether right or left handed, should use this grip. Use a firm grip with thumbs and fingers encircling the chain saw handles. Stopping The engine is stopped by pushing the stop switch to the stop position. Before use: , 1Check that the chain brake works correctly and is not damaged. 2Check that the rear right hand guard is not damaged. 3Check that the throttle lockout works correctly and is not damaged. 4Check that the stop switch works correctly and is not damaged. 5Check that all handles are free from oil. 6Check that the anti vibration system works and is not damaged. 7Check that the muffler is securely attached and not damaged. 8Check that all parts of the chain saw are tightened correctly and that they are not damaged or missing. 9Check that the chain catcher is in place and not damaged. 10Check the chain tension. General working instructions IMPORTANT! This section describes basic safety rules for using a chain saw. This informa...
Este manual também é adequado para os modelos :Benzo e serras - G5300 (13.02 mb)