Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
OXyGENATED FUELS DO NOT USE E85 FUEL. IT WILL VOID yOUR WARRANTy. NOTE: Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates stated below are not covered under warranty. Ethanol. Gasoline containing up to 10% ethanol by volume (commonly referred to as E10) or 15% ethanol by volume (commonly referred to as E15) are acceptable. E85 is not. Page 12 — English Page 13 — English operation FILLING THE fuel TANK See Figure 2. n Clean the surface around the fuel cap to prevent contamination. n Loosen the fuel cap slowly. n Carefully pour the fuel mixture into the tank. Avoid spillage. n Prior to replacing the fuel cap, clean and inspect the o-ring. n Immediately replace the fuel cap and hand tighten. Wipe up any fuel spillage. Note: It is normal for the engine to emit smoke during and after the first use. Fig. 2 ADDING bar and chain lubricant See Figure 3. Use HOMELITE Bar and Chain Lubricant. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. Chain saw should use approximately one tank of lubricant per tank of fuel. Note: Do not use dirty, used, or otherwise contaminated lubricants. Damage may occur to the oil pump, bar, or chain. n Carefully pour the bar and chain lubricant into the oil tank. n Fill the oil tank every time you fuel the engine. Fig. 3 Page 14 — English OPERATING THE CHAIN BRAKE See Figures 4 - 5. Check the operating condition of the chain brake prior to each use. n Engage the chain brake by rotating your left hand around the front handle, allowing the back of your hand to push the chain brake lever/hand guard toward the bar while the chain is rotating rapidly. Be sure to maintain both hands on the saw handles at all times. n Reset the chain brake back into the RUN position by grasping the top of the chain brake lever/hand guard and pulling toward the front handle until you hear a click. WARNING: If the chain brake does not stop the chain immediately, or if the chain brake will not stay in the run position without assistance, take the saw to an authorized service center for repair prior to use. STARTING THE ENGINE See Figures 6 - 11. Starting the product differs depending on whether the engine is cold or warm. WARNING: Keep your body to the left of the chain line. Never straddle the saw or chain, or lean over past the chain line. n Place the chain saw on level ground and ensure that no objects or obstructions are in the immediate vicinity that could come in contact with the bar and chain. n Hold the front handle firmly with your left hand and put your right foot onto the base of the rear handle. To start a cold engine: n Set the ignition switch to the RUN ( I ) position. n Make sure the chain brake is in the run position by pulling back on the lever/hand guard. n Fully press and release the primer bulb 7 times. operation Fig. 4 Fig. 5 Brake Position Fig. 6 Starter grip Run Position Fig. 7 IGNITION switch IN THE RUN POSITION n Pull choke lever all the way out to FULL position. n When the temperature is above 50°F, pull the starter grip until the engine attempts to start, but no more than 3 times. When the temperature is Page 15 — English operation below 50°F, pull the starter grip until the engine attempts to start, but no more than 5 times. n Push choke lever to RUN position. n Pull starter grip until engine runs. Note: Allow the saw to run in this position 15-30 seconds, depending upon the temperature. n Depress the trigger release and squeeze and release the throttle trigger to return the engine to idle after a total run time of at least 30 seconds. CAUTION: Failure to release partial throttle when chain brake lever is in the brake position will result in serious damage to the unit. Never squeeze and hold the throttle trigger while the chain brake is in the brake position. To Start a Warm Engine: n Set the ignition switch to the RUN ( I ) position. n Make sure the chain brake is in the run position by pulling back on the lever/hand guard. n Pull choke lever out to FULL CHOKE position then push immediately back to RUN position to set fast idle. n Pull starter grip until engine runs, but no more than 5 times. If engine does not start after 5 pulls, use cold engine starting procedure. n Squeeze and release the throttle trigger to return the engine to idle. Run P osition Fig. 9 Fig. 10 Fig. 8 choke lever primer bulb Fig. 11 STOP throttle trigger Trigger RELEASE Page 16 — English operation STOPPING THE ENGINE See Figures 12 - 13. Release the throttle trigger and let the engine return to idle. To stop the engine, move the ignition switch to the stop ( O ) position. Do not put the chain saw on the ground when the chain is still moving. For additional safety, set the chain brake when the saw is not in use. In the event that the ignition switch will not stop the saw, pull the choke lever out to the fully extended position (Full Choke ) and enga...
Este manual também é adequado para os modelos :Benzo e serras - UT10519 (18.26 mb)
Benzo e serras - UT10522 (18.26 mb)