Log:
Assessments - 2, GPA: 3.5 ( )

Instruções de Operação Nostalgia Electrics, Modelo Margarator MSB-500

Fabricante : Nostalgia Electrics
Arquivo Tamanho: 1 mb
Arquivo Nome : 714fdb9a-e88b-481d-82c9-cfff9ed7d826.pdf
Língua de Ensino: enesfr
Ir para baixar



Facilidade de uso


(Illustration A, page 3) D 7. The lid must be on and the handle must be in the upright position for the unit to operate. Flip the power switch to AC or DC (See illustration E). Turn the unit on, begin the slush process. Blend for about 10 minutes and flip the power switch to off. If needed, repeat the process to much the desired consistency. E ENGLISH 4 USING YOUR MARGARATOR – A QUICK START GUIDE (Continued) While unit is still on, place glass or a container under spigot and dispense the chosen drink by pushing the spigot up. It is recommended to have a towel under the spigot to protect against any drips. NOTE: the spigot has a locking upright position for filling multiple drink glasses or a pitcher of drinks. If spigot drips after dispensing, place glass or container under spigot and open and close the valve by pushing down and “snapping” the spigot once or twice quickly. Small ice chips can sometimes get caught in the gasket preventing it from closing completely. 9. Turn off the unit when desired consistency is achieved and it will keep the Margarita mix cold. F 10. ALWAYS DISPENSE WITH MARGARATOR RUNNING. Allow the unit to run for a good 8 seconds to mix before dispensing if unit has been sitting. NOTE: WHEN HANDLE IS LOWERED OR LID IS REMOVED WHILE THE MACHINE IS RUNNING, THE MOTOR WILL STOP RUNNING UNTIL LID AND HANDLE ARE PROPERLY REPLACED TROUBLESHOOTING PROBLEM POSSIBLE CAUSE/REMEDY Power not turning on Check the plug; make sure it is properly plugged into outlet. Make sure lid and handle are locked and handle is aligned properly Mix is not dispensing Make sure the blending cage did not loosen and float up. Make sure the unit still has liquid inside Make sure the spigot area did not freeze Make sure unit is in the ON position. CLEANING THE UNIT 1. Unplug the unit from the electrical outlet. 2. Dispense all remaining lliquid from the unit through the spigot. 3. Unlock top (See Illustration A) from base and rinse with clean water by pouring into tank and dispensing thoroughly through the spigot until clear. Wipe inside and out with a clean non-abrasive cloth or sponge. Dry with soft non-abrasive clean cloth. 4. Wipe the bottom base with a wet non-abrasive cloth and towel dry again using a soft clean non-abrasive cloth to avoid scratching the surface. Easily store your MARGARATOR ™ for the next event! By following these simple instructions, your MARGARATOR™ will be fun for friends, family, and kids of all ages...by creating delicious servings of your favorite beverages and making anytime an event. NOTE: To prolong the life of your MARGARATOR™, be sure to follow the cleaning instructions after every use and make sure the spout is flushed while washing the unit to prevent build up. ENGLISH 5 CLEANING THE UNIT (Continued) YOU MAY find a need to remove and clean the stainless grinding cage from the inside base of the tank (trapped citrus pulp, etc.) Refer to the directions below to perform this function. IMPORTANT: DO NOT PUT TANK IN DISHWASHER! REMOVING AND SETTING THE STAINLESS GRINDING CAGE IT IS VERY IMPORTANT THAT THIS THE STAINLESS STEEL GRINDING CAGE IS ASSEMBLED PROPERLY FOR YOUR UNIT TO WORK. 1. Inside the unit is a stainless steel grinding cage and round plastic collar to lock the grinding cage into place**. 2. Place the stainless steel grinding cage with the smooth side (opposite of the 3 tab side) into the plastic collar and twist until the notch of the stainless steel grinding cage locks into the protrusion on the plastic collar. (See illustration H). G 3. Turn the assembled grinding cage (with plastic cover) over, so black plastic collar is on the top to insert into the base of tank. 4. Looking down into the interior of the tank, you will see 2 Stainless Steel screws. This is where the clips attached to the plastic collar lock the grinding mechanism down. (Illustration H) 5. When putting the collar into position, align the plastic collar with the tabs with the indented postpositions. With firm but gentle pressure, press the collar down until the tabs “click” into place. H 6. Once everything is in place, make sure the clips are pushed inward toward the screws to lock the unit into position, (Illustration H) and lift slightly to insure the cage is in fact locked into position properly and will not release. **THIS IS VERY IMPORTANT! IF THE COLLAR IS NOT LOCKED PROPERLY -THE UNIT WILL GRIND BUT WILL NOT DISPENSE. Lock and unlock clips carefully, to avoid breaking. Your MARGARATOR™ is now ready to fill with your favorite liquid and use again. ENGLISH 6 6 RECIPE IDEAS Use your imagination to create many different drinks with your Margarator™. We have provided a few recipes here, in addition to the Margarita recipe on page 3. You can adjust the ingredients to your particular taste, or create your own. Keep in mind, that if you have a recipe for a drink made for ‘1’ – your Margarator™ has the capacity for 16 – 8 oz. drinks – so adjust your recipes accordingly. Basic Margarita 2 cups tequila 1.5 to 1....

Este manual também é adequado para os modelos :
Blenders - Margarator MSB-570 (1 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias