Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Issue Date OCT 2001 INSIGHTCD CHANGER ATTACHMENT KIT AII 23268 PARTS LIST P/N 08B26-S3Y-100 CD changer trim Front bracket Rear bracket Front base bracket Rear base bracket 6 EPT sealers 10 Cushion tapes 13 Short wire ties (1 not used) 8 Washer-screws, 4 x 8 mm 4 Washer-bolts, 6 x 16 mm 4 Clip nuts 2 Clips 4 Self-tapping screws 4 Flange nuts Bus cable 2 Spacers 5 Long wire ties (4 not used) CD Changer: P/N 08A26-1B1-100 CD changer 4 Washer-screws, 4 x 6 mm (Not used) Adhesive seal sheet Locking covers CD magazine Owner’s Manual © 2001 American Honda Motor Co., Inc - All Rights Reserved. Y0599D 08B26-S3Y-1000-911 of 10 TOOLS AND SUPPLIES REQUIRED TOOLS AND SUPPLIES REQUIRED Illustration of the CD Changer Installed on the Vehicle CD CHANGER (sold separately) BUS CORD INSTALLATION 3. Remove the two bolts that fasten the glove box, and remove the glove box. GLOVE BOX BOLTS 4. Remove the center lower cover by removing the two screws, releasing the 11 clips, and disconnecting the connector. SELF-TAPPING CLIP Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle.These procedures should not be attempted by “do-it-yourselfers.” 1. Write down the frequencies for the radio station preset buttons. 2. Disconnect the negative cable from the battery. CENTER LOWER COVER SCREW SCREW CONNECTOR 2 of 10 AII 23268 (0110) © 2001 American Honda Motor Co., Inc - All Rights Reserved. 5. Remove the self-tapping screws that fasten the radio, and pull the unit out toward you. Unplug the vehicle harness connector and the antenna lead from the rear of the radio. SELF-TAPPING ANTENNA SCREW VEHICLE HARNESS CONNECTOR LEAD 6. Remove the driver's door sill trim (four retaining clips). DRIVER'S DOOR 7. Detach the clips, and pull the driver's side cowl carpet down and out of the way. DRIVER'S SIDE COWL CARPET (Pull down and out CLIPS toward you.) 8. Remove the B-pillar lower trim panel (four retaining clips). Take care not to damage the retaining clips. SILL TRIMCLIP B-PILLAR LOWER TRIM PANEL RETAINING CLIP © 2001 American Honda Motor Co., Inc - All Rights Reserved. AII 23268 (0110) 3 of 10 (Position the BUS cable EPT SEALER SHORT (Position the BUS cable EPT SEALER SHORT Remove the four expansion clips that fasten the 12. Route the BUS cable above the steering shaft, floor carpet, and fold the carpet down and out of and secure it to the vehicle harness with four the way. short wire ties in the areas shown. EXPANSION CLIP FLOOR CARPET (Fold down.) Routing the BUS Cable 10. Route one end of the BUS cable up under the dashboard, and out the radio opening. Position the BUS cable connector alongside the radio connector; then secure the BUS cable and the vehicle harness with two short wire ties in the areas shown. WIRE TIES RADIO CONNECTOR 11. Attach a piece of EPT sealer to the dash support to protect the BUS cable. connector flush with the radio connector.) HOOD OPENER VEHICLE HARNESS SHORT WIRE TIES STEERING SHAFT FUSE BOX BUS CABLE 13. Route the BUS cable down alongside the fuse box, and secure it to the body panel with one cushion tape. Secure the BUS cable to the vehicle harness with the two short wire ties. CUSHION FUSE BOX SHORT WIRE TIES TAPE 4 of 10 AII 23268 (0110) © 2001 American Honda Motor Co., Inc - All Rights Reserved. 14. Continue routing the BUS cable toward the rear of the vehicle. Measure 35 mm below the door opening, and secure the BUS cable to the body with four cushion tapes. SHORT WIRE TIE 35 mm CUSHION TAPES VEHICLE HARNESS 15. Secure the BUS cable to the vehicle harness with one short wire tie in the area shown. 16. Open the tailgate, and remove the cargo floor mat. CARGO FLOOR MAT TAILGATE CARGO BOX 17. Remove the cargo box. 18. Remove the rear side trim panel (three expansion clips). REAR SIDE EXPANSION CLIP LEFT TRUNK SIDE BOARD WASHER-BOLT TRIM PANEL RELAY 19. Remove the left trunk side board by pulling out on the back and toward you. 20. Locate the relay mounted to the lower trunk panel. Remove the washer-bolt to free the relay. 21. Remove the middle bulkhead cover (pry out the seven screw covers, and remove the seven screws). SCREW SELF-TAPPING COVER SCREW MIDDLE BULKHEAD COVER © 2001 American Honda Motor Co., Inc - All Rights Reserved. AII 23268 (0110) 5 of 10 22. Remove the three clips, and fold down the top portion of the middle carpet. If the vehicle you are working on is equipped with rear speakers, remove the speakers and rear speaker holders. CLIP FLOOR CARPET (Turn over.) SCREW CLIP SPEAKER HOLDER 23. Continue routing the BUS cable toward the rear of the vehicle alongside the vehicle harness, then up and out through the cutout in the area shown. While wearing gloves to protect your hands, reach through the speaker hole, and secure the BUS cable to the vehicle harness with four short wire ties in the areas shown. SHORT WIRE TIES CUTOUT SPEAKER H...