Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Never pull the power cord. ■ Never open the cabinet. If the unit is not functioning correctly, call the Gemini Service Center at (908) 969-9000. ■ Do not use chemical solvents to clean the unit. ■ Keep the laser pickup clean by keeping the drawer closed. ■ Keep this manual in a safe place for future reference. SAFETY CERTIFICATIONS: Laser Diode Properties ^ CAUTION Material: Ga - AI - As To prevent electric shock, do not remove the cover or the Wavelength: 755 - 815 nm (25° C) bottom screws. There are no user serviceable parts inside. Laser Output: Continuous Wave Please refer servicing to a max 0.5mW qualified technician. LINE VOLTAGE SELECTION: ( ONLY FOR DUAL VOLTAGE ) Model CD-4700 is a dual voltage unit. It will operate at 115 or 230 volts. The unit is preset at the factory to 115 volts. To set the proper voltage follow these steps: 1. Place the head of a screw driver in the center of the VOLTAGE SELECTOR SLIDE SWITCH ( 15 ) found on the rear panel. 2. Slide the switch up for 115 volts or push the switch down for 230 volts. 3. Do not force or twist the switch. Excessive force may cause damage. If the switch does not move smoothly, contact a qualified technician. ASA gomini POWER SUPPLY I !5'23QV AC SQ.-fiOtU POWER CONSUMPTION MOOELD PLAYER CD 4700 SERIAL NO .ObOOCOI rO o CONNECTIONS: A typical connection with a mixer is illustrated above. Please use it as a reference. 1. Plug one end of a set of RCA connectors into the LINE OUTPUT JACKS (16 ). 2. Plug the other end of the RCA connectors into any available line level input jacks on your mixer. If you are playing the CD-4700 through a receiver, you can plug- the RCA connectors into the CD input jacks on your receiver. If there is no CD input, use AUX or any other line level (not phono). Page 2 1. POWER SWITCH: After making sure that the VOLTAGE SELECTOR SLIDE SWITCH (15), found on the rear panel, is properly set, plug the unit in and press the POWER SWITCH (1 ). The unit will turn on. Pushing the POWER SWITCH (1 ) a second time will turn the unit off. 2. DISC TRAY: The DISC TRAY ( 2 ) is where the CD is held during loading, unloading and playback. Pressing the disc tray OPEN/CLOSE BUTTON (3), will open or close the tray. The DISC TRAY ( 2 ) holds both 12 cm and 8 cm CDs. NOTE: If the CD-4700 is in the play mode, the tray will not open. 3. OPEN/CLOSE BUTTON: Press the OPEN/CLOSE BUTTON ( 3 ) to load or remove a CD from the DISC TRAY ( 2 ) 4. DISPLAY: The DISPLAY ( 4 ) shows the track number, play mode, pause mode, and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. 5. PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON ( 5 ) causes the operation to change from play to pause or from pause back to play. See the CUE INSTRUCTIONS section for more information. 6. TRACK SKIP: The TRACK SKIP BUTTONS ( 6 ) let you select the track to play. 7. SEARCH BUTTONS: The SEARCH BUTTONS ( 7 ) are used to accurately position the disc at the point where you wish the track to start playing. This position on the track is memorized as the cue point. Each push of the SEARCH BUTTONS (7) will put the CD unit in the pause mode and will move the memorized cue point 1 frame (1/75th second). See the CUE INSTRUCTIONS section for more information. 8. SEARCH DIAL: Use the SEARCH DIAL (8) to select the scanning direction and speed. Turning the dial in the clockwise direction will scan forward and counter clockwise will scan in reverse. The scanning speed increases as the dial is turned further. The SEARCH DIAL (8) will not change the cue point and will not bring the unit to the pause mode. 9. STOP: The STOP BUTTON ( 9 ) will end the playing of the CD. 10. TIME: The TIME BUTTON (10) switches the time display between the three available choices listed under #4 (DISPLAY). 11. CUE: With the unit in the play mode (play/pause LED glows green), and after using the SEARCH BUTTONS ( 7 ) to memorize the cue point, pressing the CUE BUTTON (11 ) will cause the CD player to enter the pause mode (play/pause LED blinks green) at the memorized cue point ( the cue LED glows yellow ). If the cue point was not memorized, the unit will return to the beginning of the track. 12. LOOP: After the cue point is memorized, pressing the LOOP BUTTON ( 12 ) in the play mode, (the cue LED blinks yellow), repeats the section between the cue point and the point where the LOOP BUTTON (12 ) was pressed (there will be a small space between the end and the restart of the loop). 13. PITCH: Pushing the PITCH BUTTON (13 ) activates the pitch section of the unit ( pitch LED glows red ). The pitch of the CD will change according to the position of the PITCH CONTROL (13 ). Pushing the PITCH BEND BUTTONS (14) will gradually raise or lower the pitch without changing the slide setting. Releasing the buttons will return the pitch to the slide setting. Maximum pitch deviation is +/- 8 %. Page 3 OPERATING I...