Assessments - 3, GPA: 3.7 ( )

Fabricante : Follett Arquivo Tamanho: 1.38 mb Arquivo Nome : Língua de Ensino:

Test operation. 11. Clean and sanitize icemaker following instructions in icemaker manual. Discard sanitized ice. 12. Clean and sanitize dispenser hopper following instructions on page 16. Installation is complete. Fig. 9 – Ice transport tube and ice level control stat mounting for freestanding dispensers and countertop units with Satellite-fill icemaker engaging pin 5mm (.187) ice tube hole ice hose mounting bracket capillary tube ice tube 26mm (1.00") 13 Installing top mount icemakers (models C/E25CT400A/W, C/E50CT400A/W, C/E25HT400A/W, C/E50HT400A/W) ! Dispensers with top mount icemakers cannot be mounted on legs. They must be bolted to counter. Use gloves when lifting icemaker to protect hands from sheet metal edges. 1. On dispensers equipped with topmounted, water-cooled icemakers, feed condenser supply and drain lines from back through utility knock-out (Fig. 4F) or through counter, as appropriate. Connect condenser supply line to inlet fitting (Fig. 3H) on utility flange at bottom of dispenser. Connect condenser drain line to outlet fitting (Fig. 3J) on utility flange at bottom of dispenser. Note: Do not run condenser supply water through icemaker water filter system. Do not connect condenser drain line to any other drain lines. 2. Remove dispenser top front cover by removing two screws at bottom corners of cover, lifting cover slightly and pulling forward. 3. Remove icemaker compartment top and side panels. 4. Remove icemaker hold-down bracket from front of icemaker compartment. 5. Lift icemaker onto dispenser top and slide icemaker completely into position, compressor end first. Front of icemaker base must be flush with front of dispenser. 6. Reinstall hold-down bracket on front of icemaker with power cord and bin signal cords in notch. Do not cut or pinch cords. 7. Insert loose end of ice transport tube through bracket on icemaker base into hopper access hole. Be sure that transport tube is secured under retainer on float reservoir bracket (Step 2, Fig. 10).Tighten transport tube clamp screw to secure ice transport tube. Fig. 10 – Ice transport tube 1 2 TIGHTEN 3 CLAMP SCREW 8. Connect plastic water supply line to fitting at top of float reservoir. 9. Connect vinyl drain from dispenser securely to 120° elbow on icemaker drain line. 10. Connect icemaker two-lead bin signal twist lock plug, and three-lead power connector, to dispenser twist- connectors. 11. On dispensers equipped with water-cooled icemakers, connect condenser water supply and drain lines to condenser fittings on icemaker. 12. Turn on water supply and check for leaks. Check that water level in float reservoir (when full) is within 7mm (1/4") of mark on side of reservoir, and that float moves freely. Verify that water sensor tabs are immersed in water in reservoir. Replace splash panel. 13. Install appropriate plug on power cord and insert into wall socket. 14. If dispenser is equipped with SensorSAFE remote protective plastic coating from dispense sensor labels. 15. Turn on power and bin signal rocker switches and test operation. 16. Clean and sanitize icemaker following instructions in icemaker manual. 17. Remove dispenser hopper access lid and clean and sanitize dispenser according to instructions on page 16. 18. Replace side and front covers and secure with screws. Installation is complete. 14 Fig. 11 – Ice transport tube and bin thermostat capillary tube mounting units with top mounted icemakers 19mm capillary tube Hand bend cap tube end to approx. 45° as shown 45° (.75") 15 User information How the dispenser works Follett’s 25 and 50 automatic load ice and water dispensers receive ice from Follett’s 181kg (400lb)/day icemaker located in the dispenser base, in the cabinet top or in a remote location up to 6m (20 ft) away. Ice produced is stored in the bin section of the dispenser. When the dispense lever is pushed, the wheel motor is energized, causing the wheel to turn. This moves ice to the dispense chute where it drops by gravity into the container held below the chute. In Follett’s continuous icemaking process, water freezes to the inside wall of the stainless steel evaporator. A rotating stainless steel auger carries the ice to the top of the evaporator where it is compressed and extruded through a nozzle on the outlet port. The ice is then pushed through a tube to the dispenser bin. When the storage area is full, a bin stat opens and shuts the icemaker off. When the bin is full, a bin stat shuts off the icemaker to avoid over-filling of the bin. The icemaker will restart after 20 minutes if the bin is calling for ice. How the SensorSAFE accessory works Follett’s SensorSAFE accessory maximizes sanitation and minimizes the possibility of cross-contamination by eliminating physical contact between the cup or container and dispenser. Sensors in the panel use reflected infrared light to detect the presence of the container and send a signal to a control board which then activates the appropriate components for ice or water dispe...

Baixe o seu

Para fazer o download, introduza 2 dígitos :