Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
The heat must also be on to operate the pump. 7. Turn the pump on using the PUMP switch. 8. When you want to supply shortening to the fryer, press the foot pedal. WARNING To avoid burning yourself, never touch the nozzle while the machine is in use. 9. When the fryer has enough shortening in it, release the foot pedal. 10. As needed, add shortening to the kettle, one cube at a time. Always add a cube if the shortening level drops to the tops of the legs of the cube melter. (See Figure 2-4 & 2-4A.) Figure 2-4. When to Add a Cube of Shortening. Figure 2-4A. (EZ34 ONLY) When to Add a Cube of Shortening. To add a cube of shortening, follow these steps: 1. Position the filter assembly so you can add shortening. The edge of the kettle has one or two sets of holes in it. Use the set of holes that is nearer to the heater head. When two of the filter frame’s pins rest in these holes, the filter assembly hangs vertically. (See Figure 2-5.) Figure 2-5. Positioning the Filter Frame for Melting. b. Place a solid cube of shortening on the cube melter. Let one cube melt and be pumped out before adding another cube. Do not overload the EZ Melt. Text Box: BOTTOM OF KETTLE Text Box: SIDE OF CUBE MELTER Text Box: IF SHORTENING LEVEL IS HERE OR BELOW ADD ONE CUBE OF SHORTENING Text Box: SIDE OF CUBE MELTER Text Box: BOTTOM OF KETTLE Text Box: IF SHORTENING LEVEL IS HERE OR BELOW ADD ONE CUBE OF SHORTENING. Filtering 1. Turn the fryer off. Allow the shortening to cool to 130..F/54..C. WARNING Hot shortening may cause serious injury. 2. Turn the EZ Melt off. Make sure that both the HEAT and PUMP switches are in the OFF position. 3. Make sure that the top of the cube melter is exposed. Figure 2-6. When to Drain the Fryer. Figure 2-6A. (EZ-34 ONLY) When to Drain the Fryer. WARNING When you begin to drain the fryer, the shortening in the EZ Melt must be shallow enough for the top of the cube melter to be exposed. If the shortening is deeper it might overflow when you drain the fryer, thus causing burns or other serious injury. 4. Position the shortening filter assembly on the EZ Melt kettle. The edge of the kettle has one or two sets of holes in it. Use the set of holes that is farther from the heater head. When two of the filter frame’s pins rest in these holes, the filter assembly rests horizontally on the end of the kettle. (See Figure 2-7.) Figure 2-7. Positioning the Filter Assembly for Filtering. 5. Disconnect the supply hose from the hose connector. Hold the two ends of the hose up so shortening does not drip out. Hang hose vertically over a pan so the shortening will drip into the pan. 6. Attach the rinsing hose securely to the hose connector. (See Figure 2-8.) Text Box: Side of Cube Melter. Text Box: Bottom of kettle. Text Box: If shortening level is here or below drain fryer. Text Box: If shortening level is here or below drain fryer. Text Box: Side of cube melter. Text Box: Bottom of kettle. Figure 2-8. Rinsing Hose. 7. Position the EZ Melt so the filter is directly under the drain in the fryer kettle. 8. Reach under the table and slowly open the fryer’s drain valve. 9. Move the HEAT and PUMP switches of the EZ Melt to the ON position. 10. Hold the insulated handle of the hose. Direct the nozzle into the fryer kettle. Press the foot pedal and rinse the kettle with shortening. Do not let shortening splash out of the kettle! WARNING To avoid burning yourself, never hold or touch the metal portion of the nozzle while the machine is in use. Wear protective gloves. WARNING Thoroughly clean and dry the floor if shortening, water, or other materials are spilled. Materials spilled on the floor may cause serious injury and loss of life. 11. After you have rinsed all the loose particles out of the fryer kettle, release the foot pedal. 12. After the shortening has drained out of the fryer kettle and through the EZ Melt filter, close the drain valve. 13. Turn the EZ Melt off. Make sure that both the HEAT and PUMP switches are in the OFF position. 14. Disconnect the rinsing hose assembly. Hold the two ends of the hose up so shortening does not drip out. Hang the hose vertically over a pan so shortening will drip into the pan. 15. Bring the supply hose back to the EZ Melt, holding the two ends of the hose up so shortening does not drip out. 16. Securely attach the supply hose to the hose connector. Make sure the outlet nozzle is securely mounted to the fryer, with the opening inside the kettle. 17. Move the HEAT and PUMP switches to the ON position. Press the foot pedal to supply filtered shortening to the fryer. 18. Before you filter shortening again, empty the EZ Melt filter. Follow these steps: a. Allow the filter assembly to cool to the touch. b. Lift off the filter assembly, holding it by the frame. c. Invert the filter assembly over a sink or garbage can and shake the sediment off of it. DO NOT rinse the filter. WARNING Rinsing the filter could cause water to drop into the kettle. Hot shortening could spatter and cause serious i...
Este manual também é adequado para os modelos :Dispensadores - EZ18 (1.35 mb)
Dispensadores - EZ34 (1.35 mb)