Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
@ @@@@@Power cord Connect the power plug to an AC outlet (120 V AC, 60 Hz). Note: c The monitor may be equipped with a 3-blade grounding- type plug. If you are unable to insert the plug into the outlet, contact your electrician. CONNECTION EXAMPLE Equipment which outputs Equipment which inputs video/audio signals video/audio signals From video output terminal From audio output terminal Video camera Video recorder To video input terminal To audio input terminal Video recorder Termination switch Set to OPEN for bridge connection. V I D E O IN O U T O P E N 7 5 W O U TA U D I O I N POWERCONTRASTBRIGHTCHROMAPHASEVOLUME ON OFF POWERCONTRASTBRIGHTCHROMAPHASEVOLUME ON OFF Monitor Monitor (The TM-A9UCV is not equipped with audio terminals.) Notes: c The illustration above only shows some possible connection examples, for reference. Terminal types and/or connections may differ according to the component connected. Also refer to the Instruction Manual of the component to be connected. c Before connecting, be sure to turn off the power of all the components. c For video signal connection, use only a 75 W coaxial cable. c Input and output terminals for video or audio (The TM-A9UCV is not equipped with audio terminals.) are bridge-connected. Do not apply two input signals to both (input and output) terminals at the same time. c For a bridge (loop) connection, connect each of input and output terminals on the monitor to separate video components. For example, if both of them are connected to a video recorder, the picture will shake abnormally except when in the recorder’s play mode. This phenomenon occurs due to a signal circulating around inside a certain component, and is not a malfunction. BASIC OPERATION 1.To turn the power on: Push the POWER switch. The power indicator glows green. To turn off power, push the POWER switch again, and the power indicator goes off. 2.To adjust the audio level: (TM-A9U only) Turn the VOLUME control to the right to increase the level, or to the left to decrease the level. Note: c The audio function can only be used with the TM-A9U. It is not available with the TM-A9UCV. PICTURE ADJUSTMENTS Turn a separate front panel control to adjust picture contrast, picture brightness, picture color density and picture hue respectively: n CONTRAST (picture contrast) control n CHROMA (picture color density) control Softer Clearer Thinner Denser CONTRASTCHROMAn BRIGHT (picture brightness) control n PHASE (picture hue) control Darker Brighter Purplish Greenish BRIGHTPHASE TROUBLESHOOTING Before concluding a problem has occurred, check the following points. If the problem persists after carrying out the checks, disconnect the power cord from the AC outlet and consult the dealer from whom you purchased the monitor. Note: c The audio function can only be used with the TM-A9U. It is not available with the TM-A9UCV. Problems Points to be checked Measures No power supply. Is the power plug connected to the AC outlet? Securely connect the power plug to the AC outlet. No picture or sound. Is the monitor turned on? Press the POWER switch to turn the monitor ON (see pages 4 and 5). Is an output signal coming in from a source component? Perform required settings on the output component. Is the cable connected improperly? Connect both the video/audio signal cables securely and properly (see pages 4 and 5). Normal picture but no sound. Is audio level set to the minimum? Adjust the VOLUME control (see pages 4 and 5). Is the audio signal cable connected improperly? Connect the audio signal cable securely and properly (see pages 4 and 5). Normal sound but no picture. Is the video signal cable disconnected or connected improperly? Connect the video signal cable securely and properly (see pages 4 and 5). No color, wrong color, or dark picture. Have the picture settings been changed? Adjust CHROMA, BRIGHT, CONTRAST and/or PHASE controls (see pages 4 and 6). Shaking picture. Is there a device generating a strong magnetic field (motor, transformer, etc.) near the monitor? Move it away from the monitor until the picture becomes stable. Unnatural, irregularly colored or distorted picture. Is there a speaker, magnet or any other magnetized object near the monitor? After moving it away from the monitor, turn the monitor’s power off. After 30 minutes or more, turn the power on again. SPECIFICATIONS Type : Color video monitor Color system : NTSC Picture tube : 9" measured diagonally, 90° deflection, in-line gun, vertical stripe phosphor pitch 0.5 mm Screen size (W x H) : 6-13/16" x 5-3/8" (173 x 136 mm) Scanning frequency : (H) 15.734 kHz (V) 59.94 Hz Horizontal resolution : 280 TV lines or more Video input : 1 line, BNC x 2 (with 1 bridge- connected output), 1.0 V p-p, 75 W , negative sync, bridge connection possible (termination switch provided) Audio input : TM-A9U only 1 line (monaural), RCA x 2 (with 1 bridge-connected output), 0.5 V rms, high impedance, bridge connection possible Audio power output : TM-A9U only (effective) ...
Este manual também é adequado para os modelos :Home theater - TM-A9U (147.84 kb)