Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. SPECIFIC SAFETY RULES 1) Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator. Symbol meaning V Volts --- Direct Current *1. no load speed „7 min revolution or reciprocation per minutes Rotation only -3- FOR BATTERY CHARGER & BATTERY PACK RECOMMENDED MINIMUM AWG SIZE OF EXTENSION CORDS FOR BATTERY CHARGERS AC Input Rating. Amperes AWG Size of Cord Equal to or But less greater than than Length of Cord, Feet 25 50 100 150 0 2 18 18 18 16 <> SAVE THESE INSTRUCTIONS ™, manual contajns important safety and operating instructions for battery charger EY0230. 2) Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery pack. 3) CAUTION -To reduce the risk of injury, charge only Battery Pack shown below. EY9001, EY9080, EY9065, EY9006, EY9086, EY9101, EY9180, EY9182, EY9106, EY9107, EY9136, EY9230, EY9200, EY9108 Other types of batteries may burst causing personal injury and damage. 4) Do not expose charger to rain or snow. 5) To reduce risk of damaging the electric plug and cord, pull by plug rather than cord when disconnecting charger. 6) Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. 7) An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. that pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. that extension cord is properly wired and in good electrical condition. c. that wire size is large enough for ampere rating of charger as specified below. 8) Do not operate charger with damaged cord or plug—replace them immediately. 9) Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 10) Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 11) To reduce the risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. 12) The charger and battery pack are specifically designed to work together. Do not attempt to charge any other cordless tool or battery pack with this charger. 13) Do not attempt to charge the battery pack with any other charger. 14) Do not attempt to disassemble the battery pack housing. 15) Do not store the tool and battery pack in locations where the temperature may reach or exceed 122°F (SOX) (such a metal tool shed, or a car in the summer), which can lead to deterioration of the storage battery. 16) Do not charge battery pack when the temperature is BELOW 32°F (0°C) or ABOVE 104°F (40°C). This is very important. 17) Do not incinerate the battery pack. It can explode in a fire. -4- 18) Avoid dangerous environment. Do not use charger in damp or wet locations. 19) The charger is designed to operate on standard household electrical power only. Do not attempt to use it on any other voltage! 20) Do not abuse cord. Never carry charger by cord or yank it to disconnect from outlet. Keep cord away from heat, oil and sharp edges. 21) Charge the battery pack in a well ventilated place, do not cover the charger and battery pack with a cloth, . etc., while charging. 22) Use of an attachment not recommended may result in a risk of fire, electric shock, or injury to persons. 23) Do not short the battery pack. A battery short can cause a large current flow, over heating and bums. 24) NOTE: If the supply cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, because special purpose tools are required. 25) TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS APPLIANCE HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. * Changes or modifications not expressly approved by MATSUSHITA ELECTRIC WORKS, LTD. could void the user’s authority to operate the equipment. FUNCTIONAL DESCRIPTION SŒY6406 is referred for illustration. ® Keyless drill chuck Clutch handle © Reversing lever Variable speed control trigger © Speed selector switch © Bit holder © Battery pack (EY91t»EY9108/EY920tVEY9136€Y9230) Battery pack release button Battery charger (EY0230) ASSEMBLY Attaching or removing bit Note: When at...
Este manual também é adequado para os modelos :Brocas e shuropopverty - EY6431 (500.03 kb)
Brocas e shuropopverty - EY6407 (500.03 kb)