Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Removal Turn the lock collar counterclockwise (looking from the front), then remove the bit. Keep the bit in bit holder when not in use. Remove the battery pack to expose the bit storage compartment inside the handle housing. A bit up to 50 mm (t-31/32 inch) long can be stored here. 50mm Note: If excessive play occurs in the chuek, (D secure the drill in place and tighten the chuck by turning ® clockwise, (2) open the chuck claws by unscrewing the lock collar and © tighten the screw (left- handed screw) with a screwdriver by turning it counterclockwise (viewed from the front). Attaching or removing battery pack 1. To connect the battery pack: Insert the battery pack. It snaps into place to indicate proper connection. 2. To remove the battery pack: Press the two tabs on the sides of the battery pack. Slide the battery pack out of the tool body. OPERATION Switch Operation 1. Depress the trigger switch slightly to start the tool slowly. 2. The speed increases with the amount of depression of the trigger for efficient tightening of screws and drilling. The brake operates and the chuck stops immecfiatety when the trigger is released. Reversing Switch Operation (Forward (O). Switch kxk, Reverse (O)) CAUTION: Do not operate reversing lever until the chuck comes to a complete stop. Shifting during rotation of the chuck may damage the tool. 1. For reverse rotation, set the lever to reverse. Check the direction of rotation before use. 2. After use, set the lever to its center position (switch lock). Speed Selection Choose a low or high speed to suit the use. The more the speed control trigger is pulled, the higher the speed. CAUTION: Check the speed selector switch before use. -7- Clutch Torque Setting Adjust the torque to one of the 18 possible settings or “ g" position to the job. CAUTION: Test the setting before actual operation. Set the scale at this line Note: When the brake operates, a braking sound may be heard. This sound indicates engagement of the bit lock. CAUTION: To eliminate excessive temperature increase of the tool surface, do not operate the tool continuously using two or more battery packs. Tool needs cool off time before switching to another pack. • Do not close up vent holes on body sides of the body during operation. Otherwise, the machine function is adversely affected to cause a failure. • Do not strain the tool (motor). This may cause damage to the unit. * Use the machine in such a way as to prevent the air from the body vent holes from blowing directly onto your skin. Otherwise, you may get burnt. * When operating with a Ni-MH battery pack, make sure the place is well-ventilated. For Appropriate use of Battery pack Ni-MH Battery pack (EY910a/EY920Q/EY9230) * Charge the Ni-MH battery fully before storage in order to ensure a longer service life. • The ambient temperature range is between 0°C and 40°C. If the battery pack is used when the battery temperature is below 0°C, the tool may fail to function properly. In that, charge the battery until charging is completed for appropriate functioning of the battery. Ni-Cd Battery pack (EY9106/EY9136) • Nickel cadmium battery pack requires a ‘BREAK-IN PERIOD” to reach maximum operating capacity. The “BREAK-IN PERIOD" is accomplished during normal usage during the first 6-8 charge and discharge cycles of the battery pack. After the "BREAK-IN PERIOD" is completed. the battery pack will maintain maximum operating capacity throughout the normal life of the battery pack Battery Pack Life The rechargeable batteries have a limited life. If the operation time becomes extremely short after recharging, replace the battery pack with a new one. Charging Note: When you charge the battery pack for the first time, or after prolonged storage, charge it for about 24 hours to bring the batteries up to full capacity. EY0230 1. Plug the charger into the AC outlet. Note: * Sparks may be produced when the plug is inserted Into the AC power supply, but this is not a problem in terms of safety. 2. Insert the battery pack firmly into the charger. 3. During charging, the charging lamp will be lit. When charging is completed, an internal electronic switch will automatically be triggered to prevent overcharging. -8- • Charging will not start if the battery pack is warm (for example, immediately after heavy-duty operation). The orange standby lamp will be lit until the battery cools down. Charging will then begin automatically. 4. When charging is completed, the charging lamp will start flashing rapidly. 5. When in any of the conditions that battery pack is too cool, or the battery pack has not been used for a long time, the charging lamp starts flashing slowly to indicate protective charging.Protective charging takes longer to fully charge the battery pack, than the standard charging time. (Max. charging time is approx. 90 minutes). * If a fully charged battery pack is inserted into the charger again, the charging lamp ma...
Este manual também é adequado para os modelos :Brocas e shuropopverty - EY6431 (500.03 kb)
Brocas e shuropopverty - EY6406 (500.03 kb)