Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
With heavy leather gloves on, tug on the bit and make sure it is securely attached. Check that it is straight. Note: Always use sharp bits. Dull or damaged bits may cause undue stress on the drill and possibly break causing injury. Bits are available at Harbor Freight Tools. Securely clamp your workpiece. Locate the Side Handle on the desired side of the tool. Drilling When drilling wood, place the bit at the point to be drilled. If you are drilling a hard, smooth surface, use a punch to mark the drill location. Set the Directional Switch forward. Grasp the handles firmly with both hands and slowly squeeze the Trigger (#34). Never operate the tool without the side handle. Never force the tool. Only apply light pressure when horizontal drilling. If you need more or less torque, use the torque adjustment on the top of the drill. Note: When drilling plastics or plastic coated chip board, follow the same directions as stated in number 5 for wood. Note: If a bit becomes wedged into the workpiece, stop and change the Directional Switch to the reverse position. Then slowly squeeze the Trigger to back the bit out of the work piece. When drilling metal, always use a punch to mark the drilling position. Use a lubricant to prolong the life of the bit and increase the drilling action with most metals. With steel, tin, and sheet metal use a light machine oil, with aluminum, use paraffin. Do not use lubricants with brass, copper, and cast iron. Grasp the handles firmly with both hands and slowly squeeze the Trigger (#34). Never operate the tool without the side handle. Never force the tool. Only apply light pressure when horizontal drilling. When driving screws, use bits suitable for the type and size of screw you are using. Drill a pilot hole for the screw head to bite into. Use the lowest torque setting. Grasp the handles firmly with both hands and slowly squeeze the Trigger (#34). Never force the tool. To back out a screw, stop and change the Directional Switch to the back position. Maintenance Unplug the drill while performing maintenance. Periodically check the mounting screws and tighten if necessary. Clean the unit with a damp cloth. Never use solvents to clean the unit. Inspect the chuck and remove any dirt or debris. Inspect the Carbon Brushes (#29). See FIGURE 1 on page 4. Remove the Carbon Brush Cap (#30) on top of the drill. Take the Carbon Brush (#29) out of the Brush Holder (#28). If it is dirty, use a pencil eraser to clean it. If it is worn, replace it and replace the Carbon Brush Cap (#30). If you replace one Carbon Brush, you must replace them both. Repeat the process with the Carbon Brush Cap (#30) on the bottom of the drill. LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 REV 07d Parts List PartDescriptionQ’ty1Screw1 2Washer13Chuck14Fender Ring15Felt Cover16Felt171/2 Circle Key18Spindle19Screw410Bearing111Head Shell112Gear113Needle Bearing114Needle Bearing1151/2 Circle Key116Middle Gear117Gear118Needle Bearing119Middle Cover120Bearing121Armature1PartDescriptionQ’ty22Windshield123Bolt224Stator125Bearing126Bearing Sleeve127Motor Housing128Brush Holder229Carbon Brush230Carbon Brush Cap231Right Handle132Screw633Governor134Trigger135Cable Clamp136S...