Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
J Caution! Detection devices should be used to determine the position of supply lines so that you do not damage any electrical wiring or gas or water pipes. Stay Safe! J Always disconnect the mains plug before cleaning or maintaining the fast charging device O or rechargeable battery pack Y. J Never charge the battery pack Y if the surrounding temperature is below 10 °C or above 40 °C. J The ventilation holes of the fast charging device O should never become blocked. J Whenever the screwdriver is being adjusted, transported or stored, please move the direction of rotation switch R to the middle position (lock) in order to prevent the screwdriver switching on accidentally. J High torques occur when hard surfaces are being screwed into. You should therefore hold the screwdriver very tight in order to avoid injury! L Initial Use L Charging the Battery Pack (Illustration B) Notice: A rechargeable battery pack Y that is new or has not been used for a long time has to be charged up before initial / renewed use. The rechargeable battery pack Y reaches its full capacity after approx. 3-5 charging cycles. 1. Insert the mains plug into the socket. The green charging control LED P lights up. GB/IE Initial Use 2. Place the battery pack Y in the fast charging device O. The green charging control LED P extinquishes and the red charging control LED {, now glowing, indicates the start of the charging process. The red charging control LED { extinguishes as soon as the battery pack Y is fully charged. 3. The green charging control LED P indicates that charging is complete and the rechargeable battery pack Y is ready for use. 4. Disconnect the mains plug of the fast charging device O from the socket. Remove the rechargeable battery pack Y. j A rechargeable battery pack Y must never be charged up a second time immediately after the fast charging procedure. Otherwise there is a danger that the rechargeable battery pack Y will be overcharged, thus reducing the lifetime of the rechargeable battery pack Y and the fast charging device O. j The charging device should be switched off for at least 15 minutes between charging. Please remove the mains plug. L Inserting and Removing the Rechargeable Battery Pack from the Device Inserting the Rechargeable Battery Pack: j Please move the direction of rotation switch R to the “lock” position and allow the rechargeable battery pack Y to lock into place in the handle. Removing the Rechargeable Battery Pack: j Press the side release buttons U simultaneously and remove the rechargeable battery pack Y. L Torque Pre-selection The rotary force can be adjusted by means of the torque pre-selector W. The torque levels go up to approximately 9 Nm. Once the rotary force that has been set (markings 1-15) is reached, the clutch disconnects the drive. 8 GB/IE j Select a low level for small screws and soft materials. j Select a high level for large screws, hard materials and when loosening screws. j If level 16 is selected, the clutch does not disconnect the drive. The drive chain is locked in place. Select this level if you require maximum rotary force. L Angular Position (Illustration A) j Press and hold the angular position switch E (see illustration A). j Move the device into the angular position (no intermediate setting). j Release the angular position switch E. Check whether the screwdriver has locked in place in the angular position. L Changing the Tool Inserting j Insert the bit into the tool holder Q. Removing j Remove the bit from the tool holder Q. L Switching on / off Notice: If the rotation direction switch R is located in the central / neutral position, the ON / OFF switch I is blocked. Therefore select a rotation direction before switching on, in that the rotation direction switch R is pushed through completely j To switch the screwdriver on, press the ON/OFF switch I and keep it pressed. j To switch the screwdriver off,release the ON/OFF switch I. L Setting the Speed The ON/OFF switch I has a variable speed control. Increasing the Speed j Increase the pressure on the ON/OFF switch I. Initial Use / Maintenance and Cleaning / Disposal / Information Reducing the Speed j Reduce the pressure on the ON/OFF switch I. L Reversing the Direction of Rotation Notice: If the rotation direction switch R is located in the central/neutral position, the ON/OFF switch I is blocked. The rotation direction is only to be switched when the appliance is at standstill. j Reverse the direction of rotation by pressing the direction of rotation switch R to the right or left. L Tips and Tricks By simply changing from the angled to the straight position you can work effortlessly in any position (see illustration C). Particularly when assembling furniture you can reach difficult-to-access places more easily with the slender device (see illustration D). When screwing into wood, metal and other materials, please note the following: j Before operation, check that the scewdriver bit is sitting properly, i.e. is correctly ce...
Este manual também é adequado para os modelos :Brocas e shuropopverty - PAS 2V (345.7 kb)