Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
The variable speed switch enables you to select the best speed for a particular application. The more you squeeze the trigger, the faster the tool will operate. Use lower speeds for starting holes without a center punch, drilling in metals or plastics, or driving screws. For maximum tool life, use variable speed only for starting holes or fasteners. NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided. E FORWARD/REVERSE CONTROL BUTTON (FIG. F) A forward/reverse control button (2) determines the direction of the tool and also serves as a lock off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool. To select reverse, depress the forward/reverse control button on the left side of the tool. The center position of the control button locks the tool in the OFF position. When changing the position of the control button, be sure the trigger is released. NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This and the impacting noise that the tool makes is normal and does not indicate a problem. LED WORKLIGHT (FIG. G) There is a worklight (5) located just above the trigger switch (A). The worklight will be activated when the trigger switch is squeezed. NOTE: The worklight is for lighting the immediate work surface and is not intended to be used as a flashlight. FG QUICK RELEASE CHUCK (FIG. H) NOTE: The chuck accepts 1/4 inch (6.35 mm) hex accessories only. Place the switch in the locked off (center) position or remove battery pack before changing accessories. To install an accessory, pull the chuck collar (3) away from the front of the tool, insert the accessory, and release the collar. The accessory is locked in place. To remove an accessory, pull the chuck collar (3) away from the front of the tool, remove the accessory and release the collar. H 10 90550107 PC1800ID, PC1200ID 4/1/09 9:33 AM Page 11 ON BOARD BIT STORAGE A bit storage slot is built-in to the area just above the battery. TROUBLESHOOTING Problem Possible Cause Possible Solution • Unit will not start. • Battery pack not installed properly. • Check battery pack installation. • Battery pack not charged. • Check battery pack charging requirements. • Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into charger until LED appears. • Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details. • Surrounding air temperature • Move charger and battery too hot or too cold. pack to a surrounding air temperature of above 40 degrees F (4,5°C) or below 105 degrees F (+40,5°C). SPECIAL NOTES FOR USE WITH LITHIUM BATTERIES • Unit shuts off abruptly. • Battery pack has reached its • Allow battery pack to cool maximum thermal limit. down. • Out of charge. ( To • Place on charger and maximize the life of the allow to charge. battery pack it is designed to shutoff abruptly when the charge is depleted.) For assistance with your product, visit our website at for a list of service centers, or call the PORTER-CABLE Customer Care Center at (888) 848-5175. THE RBRC™ SEAL The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the LI-ION or NI-CD battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by PORTER-CABLE. RBRC™ in cooperation with PORTER-CABLE and other battery users, has established programs in the United States to facilitate the collection of spent LIION or NI-CD batteries. Help protect our environment and conserve natural resources by returning the spent LI-ION or NI-CD battery to an authorized PORTER-CABLE service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery. RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation. MAINTENANCE Cleaning With the motor running, blow dirt and dust out of all air vents with dry air. Wear safety glasses when performing this procedure. Exterior plastic parts may be cleaned with a damp cloth and mild detergent. Although these parts are highly solvent resistant, NEVER use solvents. Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. 11 90550107 PC1800ID, PC1200ID 4/1/09 9:33 AM Page 12 REPLACEMENT PARTS Use only identical replacement parts. For a parts list or to order parts, visit our service website at You can also order parts from your nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our Customer Care Center at (888) 848-5175. SERVICE AND REPAIRS All quality tools will eventually require servicing and/or replace...
Este manual também é adequado para os modelos :Brocas e shuropopverty - 90550107 (766.13 kb)
Brocas e shuropopverty - PC1800ID (766.13 kb)
Brocas e shuropopverty - PC1200ID (766.13 kb)