Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
SYMBOL NAME EXPLANATION V Volts Voltage (Potential) A Amperes Current Hz Hertz Frequency (Cycles per Second) W Watt Power Kg Kilograms Weight Alternating Current Type of Current Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal Class II Construction Denotes Double Insulation min Minutes Time s Seconds Time ! Diameter Size of Drill Bits, Grinding Wheels, etc. No load speed No-load Rotational Speed .../min Revolutions per Minute Revolutions, Surface Speed, Strokes, etc. per Minute 1,2,3, … Ring Selector Settings Speed, Torque or Position Settings 8 CHARGING BATTERY PACK CHARGE BATTERY PACK: 1. Make sure the trigger on the Cordless Impact Wrench is in the “OFF” position and remove the battery pack from the Impact Wrench. 2. Insert the battery pack into the charger. Be sure that the battery pack is fully seated in the charger. Do not force. 3. Plug the charger into the nearest 120 volt, electrical outlet. The indicator light will come “ON”. INDICATOR LIGHTS OF CHARGER RED Power On The Charger is power on. Battery - Faulty The battery life may end or the battery voltage may be in extraordinary conditions. Please unplug the charger, then replace the battery pack. YELLOW Battery in High Temperature The battery pack is overheated. Please wait until the battery pack cools down, or take it out from the charger temporarily to be cooled off. Battery in Low Temperature The battery pack’s temperature is too low. Please wait untl the battery pack’s temperature rises to 50°F. Incorrect Battery Type The battery pack is unspecified or has failed. Please replace the battery pack with a new one. GREEN Fast Charging The battery is under Quick Charging. Fully Charged The charging is completed. Please take the battery pack out from the charger, then unplug the charger from the power supply outlet. 10 REMOVING / ATTACHING BATTERY PACK REMOVE BATTERY PACK: 1. Press both release buttons on either side of the Impact Wrench to release the battery pack. 2. Pull battery pack free of Impact Wrench. ATTACH BATTERY PACK: 1. Align the raised portion of the battery pack with the groove in the battery compartment of the Impact Wrench. 2. Press the battery pack into place. Make sure the latches are securely fastened. Do not use the Impact Wrench if the battery pack is not seated properly. CHARGER Before using battery charger, please read carefully all instructions and cautionary markings on battery charger, battery pack and product using battery. The charger will not automatically turn “OFF” when the battery pack is fully charged. The charging indicator light will remain “ON” until the charger is disconnected from the electrical outlet. Use only the charger which accompanied your product or direct replacement as listed in this manual. Do not substitute any other charger. Use only Alltrade approved chargers with your product. Do not disassemble charger. Do not use charger if it has been damaged, left outdoors in the rain, snow, wet or damp environments, or immersed in liquid. The battery pack and charger heat during charging. Place the charger on a flat, non-flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack. When the battery pack requires recharging, a 1 hour charge allows the tool to operate at full power. A charging indicator light on the charger will illuminate to show that charging is taking place. 9 RELEASE BUTTON BATTERY PACK BATTERY CHARGER OPERATING THE IMPACT WRENCH Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical outlet. Always turn the switch “OFF” and remove the battery pack before changing bits. VARIABLE SPEED TRIGGER SWITCH Never tape the trigger switch down to provide continuous high speed. The tool may fail under such conditions causing fire or personal injury. THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH: • The speed of the Cordless Impact Wrench depends on the amount of pressure you put on the trigger. • The more pressure you apply, the faster the Cordless Impact Wrench will go. • Release the pressure and the Cordless Impact Wrench will slow down. FORWARD / REVERSE AND TRIGGER LOCK LEVER Be sure the trigger is released when changing the position of the lever. Always store the tool in the “LOCKED/OFF” position. Always check the direction of the Cordless Impact Wrench's rotation before use. 12 IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES When using your Cordless Impact Wrench continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, the red light on the charger will flash. When the battery pack cools down, the red light will glow continuously to indicate fast charging mode, 1-hour charge time. This will occur when continuous use...