This will ensure that the safety of the power tool is maintained. Drill and Impact Drill Safety Warnings Wear ear protectors with impact 1. drills. Exposure to noise can cause hearing loss. Use auxiliary handles supplied 2. with the tool. Loss of control can cause personal injury. Hold power tools by insulated grip3. ping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a .live. wire will make exposed metal parts of the tool .li

A moment of inattention while operating power tools may result in serious personal injury. 11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. SKU 46804 For technical questions, please call 1-800-444-3353. Page 3 12. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Trig

Warning! Always unplug the unit when changing bits. Warning! After drilling or driving screws, the bit will be extremely hot. Do not touch it until it has had ample time to cool down. 1. Insert the Chuck Key (41) into one of the holes in the Chuck (3) and turn it counterclockwise to open the jaws. 2. Insert the bit and hand tighten it, then tighten it with the Chuck Key (41) by turning it clockwise. Carbon Brush (also found on bottom of tool) Torque Switch Figure 1 Trigger Chuck Lock Button Side

Do not leave the Charger unattended while charging. Charge the Battery on a inflammable surface. Move the Forward/Reverse Switch of 2. the Drill to its center, locked position. Push the Battery Release Button on 3. top of the Battery down, and slide the Battery off the handle of the Drill. Chuck (4) Torque SelectorLevel (18) Battery Release Button Slide the Battery onto the Charger. 4. Plug the Charger into a grounded120 volt electrical outlet. Verify that the charging indicator light 5. comes o

Lubricate the Drill Bit with cutting oil when drilling iron or steel. Use a coolant when drilling nonferrous metals such as copper, brass, or aluminum. When the hole is drilled, remove the 8. drill bit from the hole while the Drill is still running. This prevents the Drill Bit from getting caught in the hole and causing damage. Please Note: 9. The Drill/Driver has an LED light that shines on contact area. Lightly tapping on the Trigger will activate the LED light. To prevent accidents, turn off

Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. impORtant SaFEtY inFORmatiOn General power tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may r

Save thiS manual. Copyright© 2010 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. When unpacking, make sure that the pr

Wear restrictive hair covering to contain long hair. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The h

While holding the tool in your hand, for a clockwise rotation, move the Lever to the right. For a counterclockwiserotation, move the Lever to the left. (See Figure A.) TO CHARGE THE IMPACT DRIVER 1. NOTE: The Battery (40) requires charging. (See Figure A.) 2. When the Battery (40) requires recharging, a 1- 1-1/2 hour charge allows the tool to SKU 92472 For technical questions, please call 1-800-444-3353 PAGE 7 operate at full power. operate at full power. . (See Figure A.) 3. Make sure the Trigg

When tool performance begins to diminish, stop the tool, recharge the battery, and use a fully charged battery for optimal performance. When the Battery Pack-after initial charge-requires recharging, it must charge for 2. five to seven hours in order to operate at full power. Charging room temperature: 50° F. – 104° F.3. Depress both buttons at the rear of the Battery Pack and slide the unit down to 4. detach from the Drill/Driver. 5. The Battery Pack can only fit into the Charger (20) in one po