.................................................1 9...............6294132...................Shaft..................................................................... .................................................1 .............6294133...................Gear..................................................................... .................................................1 11 .............6294134 ...................C-Clip ...................................................................

Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your mortiser and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. Warranty and Service WMH Tool Group warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Repair Stations located throughout the United States can provide quick service or inf

Sheet metal outfeed table withb. height adjustment Planing and joining tables lockc. Precision ground table topd. Oversized, ergonomic knobse. Integrated cord wrapf. CFBSpecificationS Stock number 707400 Model number JJP-8BT Motor 120V, 60Hz, 13Amp Knife Size (in.) 8.25 x .65 x .06 number of Knives (RpM) 2 cutting Speed 9,000 cuts per Minute cpM 18,000 feed Speed fpM 19.5 Max. cutting Width (in.) 8 Jointer Max. cut Depth (in.) 1/8 planer Max. cut Depth (in.) .08 cutting thickness (in.) .20 - 4.9

Head mounted dual AC powered laser guide system provides an accurate drilling cross point on the workpiece. The poly v-belt drive system is quiet and vibration free. This drill press also features a built-in work light to provide direct lighting on the workpiece. An extra large 14" x 18" work table provides plenty of support for larger projects. Jettools.com FEATURES • Innovative extra large 14" x 18" work table features: twin T-slot grooves for homemade jigs. Edge lip designed for easy clamp

5. Tighten two jam nuts (A, Fig. 10). Do not over-tighten. Nuts should not contact the housing when tight. The jam nuts should be tightened against eachother. Table Tilt Adjustment CAUTION! Remove the alignment pin first and then loosen the hex cap bolt. Failure to comply may cause the table assembly to separate from the column and fall. To tilt the table: 1. Turn nut (D, Fig. 11) clockwise to pull out the alignment pin (E, Fig. 11). 2. Loosen hex cap bolt (F, Fig. 11), and tilt the table to the

......................................Handle Body (re:17373839)................................. ....................................1 38 ........17373839 ......................Feed Shaft Assy (#37,38,39) ............................... .................................... 1 39 ........ ......................................Spring Pin (re: 17373839).................................... ....................................1 43A......10604303A1..................Handle Bar Assy......................

Don't force a machine or attachment to do a job for which it was not designed. . USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your machine will draw. An undersized cord will cause a drop in the line voltage resulting in power loss and overheating. Ifindoubt,usethenextheaviergauge. Remember,thesmallerthegaugenumber,the heavier the cord. . WEAR PROPER APPAREL. Do not wear loose

The JET JFM-5 Hollow Chisel Mortiser is designed to produce extremely accurate mortises in a wide range of woods and project designs, plus make this an easy task for the woodworker. The JET JFM-5 Hollow Chisel Mortiser has been designed and built to extend its value by maintaining its performance for many years under the demands of even busy woodworking shops. We begin with a heavy-duty cast iron and steel frame for stability, accuracy and repeatability – not to mention long-term durability. Pre

Lower Work Support To use the lower work support, remove the table (see “Table Removal and Storage”). Loosen the locking handle (Figure 16) and slide the lower work support into position. Re-tighten the handle securely. Re-setting the Head The head can be adjusted in order to achieve the maximum workpiece height. 1. Place a block of wood for support between the head and fence (Figure 17). Lower the head until it rests upon the block. 2. Loosen only slightly the hex nut (A, Figure 17). 3. Pull do

POWERMATIC PM2800 18” Variable Speed Drill Press The POWERMATIC 18" Drill Press has been designed from the ground up to exceed the norm in modern drill presses. Everything from our shadow- busting dual LED work lights to the dual laser guide system, one-handle variable speed, expandable work table and class-leading horsepower make the POWERMATIC PM2800 18" Drill Press exceptionally capable and user friendly. The extensive use of high-end iron castings and heavy-duty steel components make the POW