Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Some playback operations of discs may be intentionally fixed by software producers. Since this unit plays discs according to the disc contents the software producers designed, some playback features may not be avail able. Also refer to the instructions supplied with the discs. 5. Powering the DVD Player This system MUST be powered from the type of switched (Accessory) power indicated on the marking label (i.e. not directly from the car battery). Power should be applied to the unit when the ignition key is in the Run and/or Accessory positions. Use only the supplied power cable matching this set to avoid electric hazards. 6. Operation When the temperature rises dramatically from a very low temperature, moisture may condense inside the AVD300 and cause the DVD player to malfunction. If the AVD300 does not operate properly under these conditions leave the AVD300 turned on for about half an hour until the moisture evaporates. 3 C. Contents 1. Main Unit 2. Remote control with one CR2025 Battery 3. Power Cable 4. Two (2) Brackets with four (4) Screws 5. Owner's Manual 6. Power Adaptor* (4-Pin to 2-Pin) Cable 7. DVRCA * Adaptor for connection to a second monitor 8. RCA Cables ( Red, Yellow, and White) * For use with 8010730 Accessory Cable D. Controls Main Unit (Refer to Figure 1) 10 1. Power Button 11 2. Menu Button 3. Previous Button 4. Play & NAV Up, Down, Left, Right Button 1 2 3 4 56 7 8 9 5. Next Button 6. Stop Button 12 13141519 16 17 18 7. Video Input Jack 8.Audio L Input Jack 9. Audio R Input Jack 10. Eject Button 11. Remote Control Sensor 12. S-Video Jack 13. Video Output Jack 14.Audio L Output Jack Figure1 15. Audio R Output Jack 16. Monitor Port 1 17. Monitor Port 2 18. DC 12V Jack 19. IR Input Jack 4 E. Remote Control View (Refer to Figure 2) 1) Power Button 2) Display Button 3) Angle Button 4) Subtitle Button 5) Audio Button 6) Zoom Button 7) Up/Down/Left/Right / Enter Buttons 8) Menu Button 9) Return Button 10) A-B Button 11) Forward Button 12) Reverse Button 13) Slow Button 14) Stop Button 15) Eject Button 16) Number Buttons 17) Setup Button 18) Repeat Button 19) Skip- Button (Previous) 20) Skip+ Button (Next) 21) Play Button 22) Pause Button Figure 2 5 F. Connections MMH56B/T/G REMOTE IR RECEIVER S-VIDEO OUTPUT VIDEO L AUDIO R MONITOR1 MONITOR2 12VDC INPUT A/V OUTPUT RED SWITCHED 12VDC BLACK GROUND Figure 3 1. Powering Your DVD Player ( Refer to Figure 3) Connect the black wire (-) to the vehicle ground. Connect the red wire (+) to a switched (Accessory) 12VDC source. Plug the other end into the 12VDC input jack on the rear of the unit. 2. Remote IR Receiver ( Refer to Figure 3) Plug the 1/8” jack on the remote IR cable into the IR IN jack on the rear of the DVD player. Place the IR receiver anywhere in the vehicle to allow remote control in any location. 6 AUDIOVOX DVRCA Figure 4 3. Connecting to an Audiovox Overhead Monitor a. The AVD300 can be connected to Audiovox Overhead monitors with the supplied adaptors (DVRCA and 4 pin to 2 pin power adapter) when using the Audiovox accessory cable (part number 8010730). Plug in the 3 RCA jacks, white (left audio) to white, red (right audio) to red, and yellow (video) to yellow. Connect the 2 pin IR jacks. Connect the 4 pin to the 2 pin power adapter, 4 pin to the accessory cable and the plug into the AVD300 power jack. 4. Connecting to a Monitor a. Match the color-coded plugs to the appropriate jacks on the back of the DVD Player A/V OUTPUT jacks: Yellow (video) to Yellow, White (left audio) to White, and Red (right audio) to Red. 7 Figure 5 b. Connect any of the two monitor ports on the back of the DVD player directly to the Movies To Go headrest hoods Model MMH56 B/T/G. This is plug and play, power, audio, video and IR signals are supplied in one DIN cable. c. If your TV has an S Video input connector, connect the DVD Player using the S-VIDEO connector. This connection will have a better picture. Refer to the owner's manual supplied with the TV to be used. d. Using the supplied adapter (Part Number DVRCA) the monitor port can be connected to any monitor. 5. Connecting an External Source a. To connect a video game or another audio/video source, just plug the A/V output jacks of the source into the matching color-coded A/V input jacks on the front of the DVD player. The front inputs take priority over the DVD player. G. Playing a DVD After connecting power to the unit, press the power button on the main unit momentarily. The power light will increase in brightness. Insert the disc into the slot on the front of the unit, the unit will load the disc and start playing automatically; if there’s a disc inside the unit, press the POWER button, the unit will start playing automatically. 8 1. Basic Operation POWER EJECT PLAY SLOW PAUSE STOP NEXT PREVIOUS FORWARD REVERSE UP/DOWN/LEFT RIGHT ENTER NUMBERS RETURN MENU REPEAT A-B DISPLAY ANGLE SUBTITLE AUDIO ZOOM SETUP Turn the unit on/off Eject/load the disc Start Playback Play at 1/2, 1/4, or 1/8 times speed Still...