Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Your Heath®/Zenith Chime Extender allows you to add doorbell coverage to any room in your house without the need to run additional wires.The Chime Extender "listens" for your existing doorbell to ring, then transmits a radio frequency signal to the plug-in chme unit in another part of the house. 1. Set the chime volume on the back of the plug-in chime, if desired. 2. Plug-in the doorbell chime. To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other).This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. © 2007 HeathCo LLC 595-5345-07 3. Install the Extension Transmitter. 12345678 Figure 2 1. Remove the battery cover from the Extension Transmitter by pressing on the cover with your thumb, then slide the cover off as shown Figure 2. 2. Install four AAA batteries (not provided). Make sure batteries are oriented properly (see page 5). Microphone Wire Existing Doorbell Extension Transmitter Transmit Light Test Button Microphone Microphone Sensitivity AdjustmentTerminals Figure 3 3. Note: The transmitter can be oriented horizontally or vertically. Temporarily place the Extension Transmitter in the intended mounting position. Press the Test Button. If the plug-in chime sounds, continue with step 4. If the plug-in chime does not sound, go to the Troubleshooting section before continuing with step 4. 4. With the Extension Transmitter still in the intended location, activate the existing door chime. If the plug-in chime sounds, proceed to step 7. If it does not sound, try different positions for the transmitter, or increase the microphone sensitivity (Figure 3) by turning the Microphone Sensitivity Adjustment clockwise. In some instances, it may be necessary to take the removable microphone out of the transmitter case, and mount it directly on the existing chime case or inside the existing chime case on a resonating chamber (not on chime bars). Please note–the microphone wires can be temporarily removed from the wire terminals (Figure 3) by loosening the terminals with a phillips screwdriver if wire routing through small openings in the existing chime cover is desired. There is a slot on the transmitter cover for the wires if an external mounting is required. Double-sided tape is provided to attach the microphone to your existing chime case. -2-595-5345-07 5. Adjust the Microphone Sensitivity so that it is at the least sensitive position to reliably activate the transmitter. If the sensitivity is set too high, it may false trigger on common household noises. 6. When the system is working properly, carefully mark the desired location of the Extension Transmitter, and go to step 7 for final installation. 7a - Mount with Double Sided Tape . Install the battery cover. . Peel the protective backing from one side of two pieces of the double sided tape, and apply the tape to the areas on the back of the transmitter as shown in Figure 4. Double Sided Tape Double Sided Tape Figure 4 . Remove the remaining protective backing. Carefully stick the transmitter to the exact location marked in step 6. 7b - Mount with Screws & Hollow-Wall Fasteners . Temporarily remove the batteries. . Hold the transmitter in the desired location, and mark the two mounting holes. . Set the transmitter aside.Drill two 7/32 inch mounting holes.Tap the hollow- wall fasteners into the two holes. . Hold the transmitter in place, and secure with the two screws. . Reinstall the batteries and the battery cover. Mounting Holes Figure 5 595-5345-07 -3 Code and Tune Settings Code Settings Note: Most installations will not require you to change any of the jumpers on your doorbell. WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. The transmitter and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the transmitter and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Another wireless doorbell system or other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Disconnect the power to the transmitter and chime. 2. Open the cases and locate the jumpers on both the transmitter and chime (See illustration). 3. The transmitter and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code. 4. To change the code, add and/or remove jumpers as needed. There are 128 different combinations. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for bo...