Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
The chime cover style will determine orientation. 7. A cover pin is installed on two sides of the chime base. After determining correct orientation, remove, turn over, and reinstall the cover pin located on top of chime base (see Figure 1). Illustrations may vary from actual chime unit. Figure 1 - Electronic Chime Identification (2300 Base Shown) Cover Pin Volume Control Base Orientation Marking Wire Entrance Hole Front Door Tune Selection Switch (3 Selections or 10 Selections – Depending on Model) Transformer and Push Button Wire Connections Continued Test Button 8. Determine mounting location. Note: The back of the chime base is recessed to allow the base to cover the wire hole in the wall when mounting the base to the wall. 9. Mountchimebasetowallusingscrewsandanchorsprovided(see Figure 2). (Drill 7/32" diameter pilot hole for wall anchors.) • Mount keyhole screw to wall leaving about 1/8" (3 mm) of the screw threads exposed. Note: Keyhole slot is located about 3/4" (19 mm) from top of chime. • Route wires through wire entrance hole in new chime base. • Using keyhole on back of chime base, hang base on screw. • Level chime base. • Using the slots located in the bottom of the wire entrance hole, insert second screw through whichever slot is horizontal and attach to wall and tighten. Continued Existing Chime Wires from Wall Wire Entrance Hole Cover Pin Installed Correctly Keyhole Slot Back of Chime Base Keyhole Screw Figure 2 - Mounting Chime Base to Wall Wire Entrance Hole Mounting Screw Front of Chime Base Mounting Screw Slots Existing Chime Wires from Wall Wire Entrance Hole Cover Pin Installed Correctly Keyhole Slot Back of Chime Base Keyhole Screw Figure 2 - Mounting Chime Base to Wall Wire Entrance Hole Mounting Screw Front of Chime Base Mounting Screw Slots 598-1313-00 -3 - FTR10. Connect wire “F” to screw terminal marked “FRONT”. Connect wire “T” to screw terminal marked “TRANS”. Connect wire “R” to screw terminal marked “REAR” (See Figure 3). Note: Some installations may not include rear door push button. 11. Connect diode to front push button (see page 5). 12. Press the “TEST” button to verify the transformer is connected properly and to listen to the selected front door tune. 13. Hang cover on cover pin. Note: Never use cleaners or polishes. Never use any fluids on the electronic chime mechanism. Use dry cloth to clean chime cover and base. tunE sElECtion (FRont DooR) to select a tune to play Each time the push Button is pressed: 1. Turn or slide the tune selection switch (depending upon model) to select a tune. 2. Press the “TEST” button to hear the selected tune. 3. Adjust the “VOLUME” knob to the desired volume level. Figure 3 - Electronic Chime Wiring (2300 Base Shown) Existing Chime Wires from Wall Replacement Chime Base Rear Door Push Button (if Applicable) DioDE installation instRuCtions a small electrical component called a “diode” is required for this chime to play the entire tune. this diode must be installed on the terminal screws of the front door push button (see Figure 4). If not already installed on push button, attach supplied diode as shown below. If, with the diode in place, the chime does not play the complete melody, see Troubleshooting, page 6. Figure 4 - Attaching Diode to Front Door Push Button Diode Front Door Push Button (Styles May Vary) Front Door Push Button (Styles May Vary) -5 - tRouBlEsHootinG Chime does not sound: • Check Chime: Disconnect wire from terminal marked “TRANS”. Have someone operate push button at front door while you momentarily touch the “TRANS” wire to terminal marked “FRONT”. You will see a small spark if push button, wiring, and transformer are operating properly. Repeat the steps for “REAR” terminal and rear push button. If wiring between transformer and push button(s) check out properly, replace chime. • Check transformer: Test transformer voltage output with a volt meter. If a volt meter is not available, momentarily touch the two low-voltage terminals with a screwdriver. You will see a small spark if transformer is operating properly. If no spark is evident, replace transformer. • Check push Button(s): Remove suspected push button from door frame, disconnect wire from terminals and touch bare wires together. If chime operates, push button is defective. Replace push button. Chime sounds but does not complete entire tune: • Check Diode on Front push Button:Verify diode is attached securely to push button (see page 5). Chime may not function properly if a diode is installed on more than one push button. Note: Some push buttons have pre-installed diodes. An additional diode should not be added if the push button has a pre-installed diode. If chime still does not play entire tune, replace diode (Type 1N4003-200V-1A, available at local electrical component supplier). onE YEaR limitED WaRRantY This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province. For ...