Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
In typical use, alkaline batteries will last up to three years. WARNING: To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. Figure 1 1. Install alkaline type A23 12 volt push button battery (included). Remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). See diagram inside push button for correct battery orientation. Note: If batteries are preinstalled, remove orange battery tab. 2. Install 3 alkaline “D” batteries. Make sure batteries are oriented properly (see Figure 2). 3. Test range. Temporarily position chime and push button where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 4. Adjust volume control. Adjust volume control to desired volume (see Figure 2). Cover Mounting Tabs - + - +- + Type “D” Type “D” Type “D” Chime Volume Jumpers Figure 2 © 2008 HeathCo LLC 595-5506-12 595-5506-12 -2- 5. Mount push button. Use either screws or double sided tape to mount push button. • Screw Mounting: To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). Note: Remove material in screw holes (if needed) before mounting with screws. Attach back of case to door jamb or wall (see Figure 3). Snap front of push button on. • Tape Mounting: When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 6. Mount chime. Determine mounting location. There are different ways to mount the chime depending upon the model of chime purchased. Determine which model you purchased below. Mount the chime according to the instructions for your chime. Chime with Attached Decorative Cover: 1. Drill 1/4" diameter pilot hole for wall anchor (provided) and insert anchor. 2. Screw #8 screw (provided) into anchor. Leave 1/16" gap between screw head and wall. 3. Place hanger over screw to mount chime (see Figure 4). Figure 3 12345678 Sawtooth Hanger Chime Volume Sawtooth Hanger Screw Jumpers Figure 4 595-5506-12 -3- Chime with Separate Decorative Cover: The chime base can be mounted in two different ways. The base can be mounted using the keyholes or the three mounting holes. The base may be mounted horizontally or vertically depending upon the specific model purchased. Keyhole Mounting: • Use template on back cover of manual for screw placement. Note: Make sure holes are level before drilling. • Drill two 7/32" diameter pilot holes for wall anchors and insert anchors. • Mount keyhole screws to wall leaving about 1/8" (3 mm) of the screw threads exposed (see Figure 5). • Using keyholes on back of chime base, hang base on screws. • Place chime cover over tab(s) on top of chime base. Screw Mounting: • Remove batteries from chime. • Place chime against wall and verify the chime is level. • Use chime holes as a template (see Figure 6). Drill three 7/32" diameter pilot holes for wall anchors (provided) and insert anchors. • Insert 3 screws (provided) through holes in back of chime. • Verify chime is level and tighten screws securely. • Replace batteries (see Figure 2). • Place chime cover over tab(s) on top of chime base. Keyhole Slots (Horizontal Mounting) Cover Hanging Tabs Keyhole Screw (x2) Keyhole Slots (Vertical Mounting) Screw Mounting Holes Note: Chime shown mounted vertically. Note: Chime shown mounted horizontally. Figure 6 - Inside Chime Figure 5 - Back of Chime Tune Settings Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below. • Ding (one note tune) Inside Push Button: Add a jumper to location 8. • Ding-Dong (two note tune) Inside Push Button: Remove jumper from location 8. Inside Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Inside Push Button: Remove jumper from location 8. Inside Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting. BatteryBatteryBatteryChimeVolume 1 2 3 4.5 6 7 8 1 2 3 4 5 6 7 8 Tune Setting (Not used on all models) Tune Setting Inside Push Button Inside Chime Note: Some models might r...
Este manual também é adequado para os modelos :Portas e janelas - 6270 Series (508.75 kb)
Portas e janelas - 6280 Series (508.75 kb)