Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
In typical use, alkaline batteries will last up to three years. 3. Test range. Temporarily posi- tion chime and push button where you want them mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. Case Style "A" (Shown In Vertical Position) 2. Install 3 alkaline "D" batter- ies. Make sure batteries are oriented properly. The base may be mounted in a vertical or horizontal position. The correct mounting position will depend upon the specific cover (model). Cover Mounting Tabs 1. Install alkaline type A23 12 volt push button bat- tery. Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 4). 12345678 - + - +- + BatteryBatteryBattery Chime Volume Jumpers Jumpers Chime Volume Case Style "B" © 2003 DESA Specialty Products™ 595-5506-09 4. Mount push button and chime. Keyholes Case Style "A" Back 211.16 " 2 1 / 2 " Holes Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. Case Style "A": Chime can be mounted by using 3 holes in the back of case, or by using 2 screws with keyholes. Case Style "B": Chime can be mounted by using 1 large screw (provided) with saw-tooth hanger. Securely fasten saw-tooth hanger to rear of case using screws (or nails) provided (see illustration on page 1). It can also be placed on a flat surface. 5. Slide chime cover onto top of chime. Use technique for the style case you have. Mounting groove in cover will align with mounting tab(s) on base. -2-595-5506-09 Clock Chimes Battery Installation and Setting Time Note: This feature is only available on specific models. Dial Battery Cover 1. Install battery into clock. Firmly grasp brass Time Setting ring and carefully pull forward to remove clock assembly from front of chime. Gently pull off battery cover located on back of clock assembly. Install "AA" battery according to polarity marks inside battery chamber. Replace battery cover. 2. Set time. With battery cover removed, turn time setting dial on back of clock assembly until time is correct. Replace battery cover. Replace clock assembly into chime face by pressing assembly gently into hole on chime face. 3. Install batteries into chime. Remove clock chime back. Grasp cutouts on back of chime with fingers. Gently push back up and pull lower part of back out to remove. Install 3 alkaline "D" batteries according to polarity marks inside battery chamber. Replace back of chime by following the above instructions in reverse (see illustration on page 1). Code and Tune Settings Code Settings Note: Most installations will not require you to change any jumpers on your chime and push button. The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Open the cases and locate the jumpers on both the push button and chime (See illustration on page 4). 2. The push button and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code. 3. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to function. 595-5506-09 -3 Tune Settings Your Heath®/Zenith wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below. • Ding (one note tune) Push Button: Add a jumper to location 8. • Ding-Dong (two note tune) Push Button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected Heath®/Zenith chimes) Push Button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. You may purchase any Heath®/Zenith wireless push button for a second entrance. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected Heath®/Zenith chimes). Models that include two push buttons will come factory set for front and back doors. Decals ...
Este manual também é adequado para os modelos :Portas e janelas - 6280 (523.81 kb)