If it does not work, see TROUBLESHOOTING. 4. Use back cover of push button as a template to mark two screw holes. 5. Drill two holes with 3/32” size drill in marked locations. 6. Secure back cover to the mounting surface with two supplied mounting screws. 7. Press front housing onto back cover. 8. Test operation. If the chime does not work, see TROUBLESHOOTING. Operation 1. Slide power switch to “High” or “Low” to power the chime. 2. Gently press transmitter button to sound chime. Troubleshootin

1. Remove the battery from the push button transmitter. 2. Locate the 3 dip switches shown below. 3. Select the desired chime sound from the table below. ON: Switch On OFF: Switch Off - Chime Dip Switches(Ding Dong Shown) House Code Jumpers Chime Dip Switches(Ding Dong Shown) House Code Jumpers Pushbutton Dip Switches and Jumpers Setting The House Security Code Each chime component has 4 jumpers for setting the house security code. In most cases you will not need to change the factory settings f

3. Remove the battery pack and discard appropriately. Required Tools: Small flat blade screwdriver, drill, drill bit, and phillips screwdriver. Included Hardware: (2) Plastic screw anchors (2) 4x20mm screws (for anchors) (2) 3x20mm screws (2) Double sided adhesive pads The wireless door chime Kit has two components: Chime (receiver) Push-Button (Transmitter). Chime Tune Setting All wireless chimes may have more than one push button. The chime tune for each push button is set with jumpers 7-9. Si

The chime and pushbutton must be set to the same house security code for the combination to operate together. Note: The push button has 3 additional jumpers that are used to set the chime tune that will play. The chime tune jumpers do not affect the house security code. 1. Remove power or batteries from the chime. 2. To remove the batteries from the pushbutton, open the pushbutton case as shown below. 3. Locate the House Security Code door and screw located on the back of the AC Chime. Remove th

USE ON ANY OTHER FIREPLACE OR APPLIANCE MAY CONSTITUTE A POTENTIAL FIRE HAZARD. • Avoid building extremely large fires, as the tempered glass could become damaged. • Use fireplace tools carefully to avoid striking the glass. • Keep wire mesh screens closed during fireplace use. • Fireplace flue damper must remain open until fire is completely out. • Ensure that wood and embers are well within the confines of the grate area and well away from the glass doors. • Keep wire mesh screens closed durin

IF THE GLASS IN THE BI-FOLD DOOR ASSEMBLY BECOMES SCRATCHED OR CHIPPED, REPLACE THE DOOR ASSEMBLY. CLEANING • NEVER CLEAN THE GLASS WHEN THE DOORS ARE HOT. • Ammonia-based cleaners will damage the finish. DO NOT USE AMMONIA OR AMMONIA-BASED GLASS OR HOUSEHOLD CLEANERS TO CLEAN THE GLASS OR DOOR FRAME. • Take care not to scratch the glass surface. DO NOT USE ABRASIVE CLEANING PRODUCTS OR MATERIALS. To remove dirt and grime from the doors, gently scrub with a soft cloth dampened with water; and th

WARNING Pivot PinRoller PinUpper DoorGuide TrackSpring Clip DO NOT BURN TRASH, CONSTRUCTION SCRAPS, RAILROAD TIES, OR OTHER HIGHLY FLAMMABLE MATERIAL IN THE FIREPLACE. INTENSE HEAT CAN CAUSE THE GLASS TO LOSE STRENGTH AND RESILIENCE, WHICH WILL RESULT IN GLASS BREAKAGE. (continued on next page) Figure 9 LENNOX HEARTH PRODUCTS • BI-FOLD GLASS DOORS • LBF SERIES • INSTALLATION INSTRUCTIONS GENERAL OPERATING PRECAUTIONS AND INSTRUCTIONS (continued from previous page) WARNING WARNING FRONT-OPEN FIRE

Step 7. Position the center clip as shown in Figure 5, below, and attach it using the two (2) provided screws. Step 8. Proceed to bi-fold door installation procedures on the next page. (Detail: Installation of left air deflector.) (Detail: Installation of center clip on top of both air deflectors. Figure 3: Installation of Air Deflectors and Center Clip on 36LBF/LBF-BS and 42LBF/LBF-BS (Detail) Figure 5: Installation of Center Clip on 50LBF/LBF-BS LENNOX HEARTH PRODUCTS • LBF SERIES BI-FOLD GLAS

THE QUALIFIED AGENCY PERFORMING THIS WORK ASSUMES RESPONSIBILITY FOR THIS INSTALLATION. Figure 1 GENERAL INFORMATION The bi-fold glass door assemblies listed in this Instruction Sheet are designed for use with Lennox Hearth Products fireplaces or appliances that specify 36", 38", 42", 43", or 50" LBF Series doors. Each door assembly consists of a right and left glass panel assembly with factory-mounted door handles. 36LBF Series and 42LBF Series door kits also include air deflectors. 50LBF Serie

IF THESE INSTRUCTIONS ARE NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. THE QUALIFIED AGENCY PERFORMING THIS WORK ASSUMES RESPONSIBILITY FOR THIS INSTALLATION. Figure 1 GENERAL INFORMATION The bi-fold glass door assemblies listed in this Instruction Sheet are designed for use with Lennox Hearth Products fireplaces or appliances that specify 36", 38", 42", 43", or 50" LBF Series doors. Each door assembly consists of a right and lef