Note: The alert is also triggered when you undo the cover to replace batteries in the door camera. MIC volume [For future use] The topmost control along the side (see diagram on page 8) will control the volume produced from a microphone. Adjust for optimum listening level. Scan button When used in a multi-camera system, this button scans through available pictures. Privacy Remember that this product uses the public airwaves, and that the 30-second duration video signal from the door camera(s) ca

Before you mount the door camera or receiver in a permanent place, make sure that you have tested the two units and that the system works in the location you have chosen! (See ‘Setting up’, beginning on the next page.) THE VISIOCAM SYSTEM Your Honeywell wireless video entry system uses radio signals to transmit a video picture of the caller from the door camera to the receiver. The system is expandable, so you can install additional surveillance cameras, or a second door camera if required. CHEC

• Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. • Chime is for indoor use only. • Avoid mounting location which can expose chime to splashing or dripping liquid. • Use UL approved transformer for connection to mains. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like; danger of damage if battery is incorrectly replaced. Replace on

Illuminated bell push buttons can be used when the chime is powered by a transformer (Honeywell RCA900N). Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. • Chim

safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like; danger of damage if battery is incorrectly replaced. Replace only with the same or equivalent type. 1. Checking Pack Contents • Chime • Bell push • CR2032 battery for bell push • 2 x screws

To save the tune selected, press and release programming button. Note: Pressing the program button for more than 15 sec will erase all memory. Follow step 3 to re-program. M27183 M27145 4. Install Back Cover Using Screws or Adhesive Pad Provided Note: Before final installation adjust distance and position between push and chime to optimize the chime within your environment. Dense walls and metal can reduce range. TOPTOPM27184 Wall Type Range Reduction Dry-lined partition wall 10–30% Single-layer

(Model No. RPWL30XXX series, and RCA901N and RCA902N.) Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. Decorative Wire Free Chimes and Push Checking Pack Conten

Installation Instructions RCWL35 Series RCWL35N, RCWL3501A, RCWL3502A, RCWL3503A, RCWL3504A, RCWL3505A, RCWL3506A Decorative Wire Free Chimes and Push 69-2115EFS-05 Installation Instructions 69-2115EFS—05 ii Contents Safety...........................................................2 Checking pack contents.............................2 Open bell push............................................3 Install the push battery...............................3 Open the chime................................

The last tune played will be stored after the icon stops flashing. To confirm, press the push button and chime will play the tune you want. Installation 7. To add new push/reprogram Press and hold the program button l. The icons will illuminate in sequence. Release the program button when icon you choose is illuminated. Operate your new push and the chime will play tune, icon will flash. To change tune, refer to step 6. 8. Unlearn procedure To remove a push from the chime’s memory, press and hol

Follow manufacturers’ advice on the paint/vanish. It is possible to unscrew the four screws shown below for painting. Ensure you screw it back with the same screws provided! Once completed, clip it onto the base as in step 11. Installation Specification Chime Bell push Operating Temperature 32°F to 104°F 0.C to 40.C 14°F to 104°F -10.C to 40.C RF Frequency- US 916.8 MHz 916.8 MHz Range (open field) 450 ft. (140 m) Sound Level (typical) 90dBA @ 3 ft. (1 m) - RF Power - <1mW Battery Type LR14 (C s