Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Use plenty of it. Worn parts can be expensive to replace. Keep your supply of lubricating oil and grease stored in clean containers, and covered to protect from dust and dirt. Keep the lubricating gun nozzle clean and wipe dirt from grease fittings before lubricating. The symbol in the illustration indicates the method of application and the hourly intervals to apply the lubricant. Use a pressure lubricating gun and apply 251H EP grease (or equivalent No. 2 multi-purpose lithium grease). Lubricate at hourly intervals indicated on symbols. 42 LUBRICATION GUIDE 1. Engine filler cap and dipstick 2. Steering knuckles (2) (Both sides) 3. Front axle pivot bolt (Right side) 4. Engine oil drain plug 5. Steering gear 6. Front wheel bearings 7. PTO clutch bracket 8. Deck spindles Speed Control Linkage 9. Cam plates (1020 Tractor) Miscellaneous Brake pedal shaft —BEFORE EACH USE Check the oil (with the engine stopped) and add sufficient new oil to bring it to the "FULL" mark on the dipstick. Do not overfill. Do not operate the engine if the oil level is below the "LOW" mark on the dipstick. ■AFTER EVERY 10 HOURS OF OPERATION Use 251H EP grease or equivalent No. 2 multi-purpose lithium grease and apply sufficient grease to flush out old grease and dirt. Use 251H EP grease or equivalent No. 2 multi-purpose lithium grease and apply sufficient grease to flush out old grease and dirt. NOTE: It may be necessary to rotate the front axle to reach the grease fitting. AFTER EVERY 25 HOURS OF OPERATION While the engine oil is warm, remove the drain plug and drain ail of the oil from the crankcase. Replace the drain plug. Refer to "MAINTENANCE" "FILLING THE CRANKCASE" for proper oil filling procedure. Refer to "LUBRICATION TABLE" for the proper quantity and viscosity to use. -AFTER EVERY 50 HOURS OF OPERATION Turn the steering wheel fully to the right and brush on 251H EP grease or equivalent No. 2 multi-purpose lithium grease to the steering gear. Turn the steering wheel in both directions to disperse the grease. Use 251H EP grease or equivalent No. 2 multi-purpose lithium grease and apply two or three strokes or sufficient grease to flush out old grease and dirt. Use 251H EP grease or equivalent No. 2 multi-purpose lithium grease and apply sufficient grease to flush out old grease and dirt. Use 251H EP grease or equivalent No. 2 multi-purpose lithium grease and apply sufficient grease to flush out old grease and dirt. —EVERY 100 HOURS OF OPERATION Once a year, apply a small amount of 251H EP grease or equivalent No. 2 multi-purpose lithium grease in the slots. Lubricate the brake pedal shaft and linkage with eight or ten drops of engine oil. NOTE Lubrication information for optional equipment may be found in the manual which is included with the specific piece of optional equipment. LUBRICATION GUIDE MODEL 1015 4. INITIAL OIL CHANGE AT 5 HOURS, AND EVERY 25 HOURS THEREAFTER. 44 SPECIFICATIONS CAPACITIES Fuel Tank...................................... Crankcase .................................... TRANSMISSION GEARS Speed: Forward............................ Reverse............................ HYDROSTATIC DRIVE Speed: Forward............................ Reverse............................ ENGINE Make and model........................... (electric starting)........................... Cylinders....................................... Bore.............................................. Stroke ........................................... Displacement (cubic inches) ........ Engine speed................................ Low speed.................................... High idle speed (no load).............. Ignition.......................................... Sparkplug .................................... Spark plug gap ............................. ELECTRICAL SYSTEM System voltage............................. Battery.......................................... Alternator...................................... Fuse (auto type) ........................... Headlights (bulb) .......................... BRAKES ........................................ CLUTCH ......................................... TIRE SIZES Front ............................................. Rear.............................................. GENERAL Wheelbase.................................... Length, over-all............................. Turning radius............................... Mower size ................................... Adjustable cutting height (approx) Mower drive.................................. 1015 1020 3 gals. 3 pints 5 forward speeds and 1 reverse 0 to 5.5 mph 0 to 2.35 mph 0 to 5.5 mph 0 to 3.0 mph Briggs and Stratton 10 HP 1 3.44 in. 2.62 in. 24.36 (governed) 1750 RPM 3300 RPM ±100 Battery Cub Cadet No. 759-3331 .030 in. gap 12 volt neg. ground 1 HPRLU Tri-circuit 20 amp GE 12 volt 1156 Single disc, external V-belt 15x6x6 18x8.5x8 45.0 in. 68.50 in. 29...
Este manual também é adequado para os modelos :Cortadores de grama - 1015 (4.6 mb)