Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Additional rope may be wound around the starter handle. If so, unwind the rope from the handle. 2. With the spark plug wire disconnected and grounded, depress the blade control handle and pull the rope out of the engine. 3. Place the rope guide around the starter rope, so the rope guide is positioned as shown (bends downward slightly). Insert the rope guide through the right side of the lower handle, and secure with -hex lock nut. See figure 5. INSTALLATION OF HUB CAPS (Optional) 1. If your mower is equipped with hub caps which have four tabs, line up the tabs on the hub caps with the holes in the wheels. Push to lock in position. 2. If your mower is equipped with 2" wide tires, place hub caps in position against the inner hub of the wheel. Press firmly around the center portion of hub cap in a circular motion, similar to installing -a lid on a round, plastic container. See figure 6. The hub caps are flexible and will snap over the 3V2" diameter wheel hubs. NOTE: It may be helpful to place the hub caps in hot tap water for several minutes to make them pliable before installing, especially if the temperature is less than 60° F. 6 FIGURE 7. FINAL ASSEMBLY OF MOWER Make certain all nuts and bolts are tightened securely. ASSEMBLY OF GRASS CATCHER (Hardware F) NOTE: Make certain the grass bag is turned right side out before assembling (warning label will be on the outside). 1. There are three holes in the rear frame. With the -holes on the upper side as shown in figure 7A, insert one end of the rear frame into the cloth channel on the edge of the grass catcher bag. Feed all the material on one side of the frame, then work it around the frame. See figure 7B. 2. Slide the ends of the front frame assembly Into the —ends of the rear frame as shown in figure 8A. 3. Secure front of bag to front frame by slipping plastic channels on sides and bottom of bag over frame. See figure 8B. FIGURE 8. 4. Attach the hardtop cover to the grass catcher as —follows. See figure 9. a. Place the cover in position on top of the grass catcher. Press the rear frame into the channel on the rear of the cover (beneath the rear handle). b. Slide the notches on the sides of the cover over the front catcher frame. c. Attach rear of cover to frame using the flat washer and one self-tapping screw as shown in figure 9. Attach the sides of the cover to frame with the other two self-tapping screws. 7 5. Assemble the locking lever as follows: a. Place wave washer on shoulder bolt (crowned side of washer goes against the head of bolt). b. Insert shoulder bolt up through hole in hardtop cover as shown in figure 10. Place “star” -washer over shoulder bolt. Thread shoulder bolt into the grass catcher locking lever, using a 9/16" socket wrench. Do not overtighten. Locking lever must be able to pivot. c. Rear Deflector ATTACHING BAG TO MOWER Lift the rear deflector on the mower. Place the loops on the grass catcher frame over the pins on the back -of the mower. See figure 11. Release the rear deflector. Turn the locking lever to the locked position to secure the rear deflector (hardtop grass bags only). See figure 11, inset. To remove the grass catcher, turn the locking lever to the unlocked position and lift the rear deflector on the mower. Lift the grass catcher up, over the pins on the back of the mower. Release the deflector. FIGURE 11. CONTROLS FIGURE 12. BLADE CONTROL HANDLE A WARNING: This control mechanistfi is a safety device. Never attempt to bypnss its operations. The blade control handle is located on the upper handle of the mower. See figure 12. The blade control handle must be depressed in order to operate the unit. Release the blade control handle to stop the engine and blade. A WARNING: The blade will be rotating whenever the engine is running. THROTTLE CONTROL The throttle control is located on the side of the upper handle. It is used to regulate the engine speed. A WARNING: The throttle control cannot be used to stop the engine. RECOIL STARTER The recoil starter handle is attached to the handle. See figure 12. Stand behind the unit in the operating position to start the unit. 8 OPERATION TO REDUCE THE RISK OF INJURY, DO NOT OPERATE MOWER UNLESS REAR TRAILING SHIELD AND THIS GUARD OR ENTIRE GRASS CATCHER IS IN ITS PROPER PLACE. Metal Loop on Spark Plug Wire FIGURE 13. Keep hands and feet away from the chute area on cutting deck. See figure 13. The operation of any lawn mower can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields. We recommend wide vision safety mask for over spectacles or standard safety glasses. NOTE: For shipping purposes your mower is set with the wheels in a low cutting height position. For best results raise the cutting position until it is determined which height is best for your lawn. See cutting height adjustment section. GAS AND OIL FILL-UP Service the engine with gasolin...
Este manual também é adequado para os modelos :Cortadores de grama - 111-433R000 (1.9 mb)
Cortadores de grama - 111-435R000 (1.9 mb)
Cortadores de grama - 111-436R000 (1.9 mb)
Cortadores de grama - 111-438R000 (1.9 mb)