Assessments - 5, GPA: 4.2
(
)
)
|
Facilidade de uso
Personal bodily injury can result when these instructions are not followed. The information is for your safety and it is important! The safety decals below are on your product. If any decals are lost or damaged, replace them at once. See your local dealer for replacements. TP 600-2562-01-AT-SMA These labels are easily applied and will act as a constant visual reminder to you, and others who may use the equipment, to follow the safety instructions necessary for safe, effective operation. Attachment Decal Thrown objects hazard • Objects thrown by the mower can seriously injure or kill you. • Do not open the hopper while the mower blades are turning. • Do not operate the mower without the complete catcher in place. WARNING 1732819 Decal - WARNING Thrown Objects Hazard Part Number 1732819 Read and obey all operation and warning decals. 2 General Operating Instructions Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the underside of the catcher lid are free from grass and debris. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover. Mowing with the Catcher Always operate with throttle at full speed when mowing. Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging. If grass is long, operate with mower in high cutting position for first pass, cutting again in a lower position on a second pass. Do not open the cover with mower engaged. If a large amount of cut grass is spilling out from under deck, the tube may be plugged or the bags may be full— discontinue mowing, stop the unit, disengage the PTO, shut off the engine and then empty the catcher or clear the tube. WARNING ALWAYS shut off the tractor. Disengage the PTO, and allow all moving parts to stop BEFORE disconnecting or clearing tube, or emptying catcher. Before leaving the operator’s position for any reason, engage the parking brake, disengage the PTO, stop the engine and remove the key. To reduce fire hazard, keep the engine, rider and mower free of grass, leaves and excess grease. Do not stop or park rider over dry leaves, grass or combustible materials. CAUTION Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet, as well as the Operator’s Manual for the tractor and any other attachments. Never operate on slopes greater than 17.6% (10°). After Operation Remove any debris from the the screen on the underside of the lid. The blower housing and tube should be removed for cleaning. Inspect the grass bags for wear or damage. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover. CAUTION Do not leave grass in bagger containers. Empty containers after each use and before storing. Failure to do so may result in spontaneous combustion which could develop into a fire. Storing The Grass Catcher Clean the grass catcher thoroughly using a mild detergent (other products may damage the tube). Remove any debris from the the screen on the underside of the lid. If paint has been scratched on metal parts, touch up with paint, or apply a thin film of oil to prevent corrosion. Store in a dry area. Dry thoroughly before storing for a long period of time. Always store away from moisture. 3 Initial Installation 4 Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). WARNING Figure 1. Install Spacer (left side shown) A. Speed Nut, 5/16-18 B. Threaded Side C. Square Hole D. Shoulder Bolt, 5/16-18 E. Rear Frame Support B C D A A E Figure 3. Hitch Installation A. Hitch B. Shoulder Bolt C. Pin D. Hole in Draw Bar E. Hair Pin A B D E C Initial Installation HITCH INSTALLATION 1. Slide the 5/16-18 speed nut (A, Figure 1) onto rear frame support (E) through square hole (C) so that the threaded side (B) is on the inside of tractor. 2. Secure the 5/16-18 shoulder bolt (D) as shown. 3. Repeat on the other side. B C D A Figure 2. Frame Plate Reinforcement Installation A. Frame Reinforcement B. Rear Frame Support C. Frame Support Hole D. Capscrew, 5/16-18 x 1-1/4 (new) E. Locknut, 5/16-18 (existing) F. Capscrew, 5/16-18 (existing) 4. Remove existing nuts and capscrews from both sides and rear frame support holes (C, Figure 2) 5. Secure frame reinforcement (A) to the inside of the rear frame support (B) using new 5/16-18 x 1-1/4 capscrews (D) and existing 5/16-18 capscrews and locknuts (E & F) ...
Este manual também é adequado para os modelos :Cortadores de grama - 1733866 (767.61 kb)