794251 1................................................Head Ass'y., L.H. (incl. items 2 thru 16) 2................................................Self-tapping screw, Rd. Hd. IQ- 24 x 1/2 3................................................Cover 4................................................Gasket, Cover 5................................................Ring, Snap 6................................................Gear, Miter 7................................................Bearing,

ELECTRICAL SYSTEM I. DRIVE TRAIN IV. FUEL SYSTEM V. CHASSIS VI. HYDRAULIC SYSTEM VII. ENGINE VIII. TRACTOR ATTACHMENTS f?j bi pa pn ra ra ra MEDIUM FRAME SERIES TRACTOR Rev. 11-90 TABLE OF CONTENTS GROUP 1. GENERAL SERIAL NUMBER INFORMATION...............1-1 SPECIFICATIONS..............................1-2 MAINTENANCE CHART........................1-5 LUBRICATION POINTS (GEAR DRIVE) .........1-6 LUBRICATION CHART (GEAR DRIVE)..........1-7 LUBRICATION POINTS (HYDROSTATIC DRIVE)..

If you cannot locate an authorized service dealer, contact the manufacturer as set forth on your copy of the Owner’s Registration Card. 1. The blade brake/clutch hand control is a safety device. Never attempt to bypass its operation. Doing so makes the safety device inoperative and may result in personal injury through contact with the rotating blade. This hand control must operate freely in both directions. 2. Striking a solid object can cause damage to the blade brake/clutch or to the engine

v Check that the ventilation slots are not obstructed in any way. Do not use your Turbotrimmer if the safety devices (push button, safety cover) and/ or the filament cassette are damaged or worn. v Never bypass the safety devices. v Inspect the area to be cut before you begin work. Remove any foreign objects (such as stones). Look out for foreign objects (such as stones) while you are working. v If you should come across an obstacle while cutting, turn off the Turbotrimmer. Remove the object and

770-0840 INDEX Safe Operation Practices .3 Using Your Rotary Mower . 4 Off-Season Storage..... 10 Exploded Parts View..... 11 Repair Parts List........ 12 Parts Information....... 12 ........14 ........14 .....16, 18 .....17,19 Back Cover Assembly Operation Adjustments Lubrication. Maintenance LIMITED WARRANTY For one year from the date of original retail purchase, MTD PRODUCTS INC will either repair or replace, at its option, free of charge, F.O.B. factory or authorized servic

Allow the engine to cool before storing in any enclosure. 4. To reduce fire hazard, keep the engine free of grass, leaves, or excessive grease. 5. Check the grass catcher bag frequently for wear or deterioration. For safety protection, replace only with new bag meeting original equipment specifications. I Hairpin (T) Handle Loop Handle HANDLE IDENTIFICATION The hairpin (T) handle will mount to the deck with shoulder bolts, nuts and lock washers. For models with remote throttle control, t

(Optional) (Optional) 26 712-0116 Hex Ins. L-Nut 3/8-24 Thd. 57 12945 Handle Mount Brkt. Ass’y. (Optional) (Optional) 27 736-0105 Belleville Wash. (Optional) 58 714-0104 Hairpin Cotter (Optional) 28 10937 Pivot Bar (Optional) 59 12946 Handle Mount Brkt. Ass’y. 29 14082 Spring Lever Ass’y. w/Knob (Optional) (Optional) 60 710-0603 Hex Wash. Hd. Self-Tap 30 710-0209 Hex Sems Bolt 3/8-16 x .62" Scr. 5/16-24 x .50" Lg. Lg. (Optional) (Optional

After assembly, see operating section of this manual for proper fuel and engine oil recommendations. Your new mower is shipped preassembled with the exception of the handle and wheels. 1. Remove lawn mower and all parts from the carton. Make certain that all loose parts and literature have been removed before the carton is discarded. NOTE Throttle control may be optional on your unit. 2. Extend throttle control assembly which is attached to engine at the rear of the mower and place on floor

Remove metal from the heavy side until it balances evenly. See figure 17. It is recommended that the blade always be removed from the adapter for the best test of balance. FIGURE 17. C. Reassembly Before reassembling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner surface of the blade adapter with light oil. Lubricating the bolt holes, bolts and inner surface of the nuts with light oil is also recommended. A 4 oz. plastic bottle of light oil lubrica