Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
See figure 9. The large holes in the support tube mounting brackets go to the left side of the unit. The flange in the brackets go toward the top. c. Secure with hex bolts (N), lock washers (O) and hex nuts (P), finger tight only. After all eight hex bolts and nuts are assembled, then tighten securely. NOTE: It may be necessary to spread the support brackets slightly in order to align the holes. 30" & 32" Decks 36", 38", 42" & 46" Notch Latch Support Bracket Support Tube Mounting Brackets Lock Washer FIGURE 10. Hex Bolt (K) ex Nut (M) 30" & 32 Assemble the latch support bracket to the right side of the support tube mounting brackets using the upper set of holes in the latch support bracket as shown in figure 10. Assemble so the notch in the top of the latch support bracket is toward the rear of the unit. Secure with two hex bolts (K), lock washers (L) and hex nuts (M). ASSEMBLY OF COVER . (Group B) Place the support tube assembly in position on the rear of unit by sliding the support tube down through the holes in the left side of tube mounting brackets. Use the inside hole for 36", 38", 42" and ' 46" decks. Use the outside hole for 30" and 32" decks. See figures 10 and 11. 36" 38", 42“ & 46'^ Support Tube Assembly 2. 3. Shoulder Bolt (F) Belleville Washer (G) 4. FIGURE 11. Lock Hex Washer (H) Nut (I) Place belleville washers (G) on shoulder bolts (F) so that the crowned side of the washers is against the head of the shoulder bolt. Place the cover in position against the brackets on the support tube assembly as shown in figure 11. (Allow the cover to rest on the seat of the lawn tractor for ease of assembly.) Line up the holes in the hinges of the cover with the holes in the support tube. Insert the shoulder bolts (with washers attached) through the hinges on the cover and the support tube assembly. Heads of the shoulder bolts go toward the inside of the unit. Secure with lock washers (H) and hex nuts (I). Do not overtighten. Cover must be able to pivot on the support tube. 5 Discharge Chute FIGURE 13. Chute Tube 5. Attach the grass bags using the slots shown in **-figure 12. 6. Close the cover on the grass collector. ATTACHING THE DISCHARGE CHUTE TO THE TRACTOR 1. Raise the deck to its highest position. Raise the chute deflector on the deck. Place the top edge of discharge chute in position over the chute opening on the deck, then push down on discharge chute so the front edge locks into clip on deck. -See figure 13. 2. Lock discharge chute in position by hooking retainer strap over the second clip on the deck. 3. Insert the upper end of the chute tube into the — hole in the cover. See figure 14. 4. Place the lower end of chute tube over the discharge chute. See figure 14. Secure by placing the ends of the retainer straps on the discharge chute over the retainer clips on the chute tube. 6 OPERATION *\ To open the cover, simply lift up on cover. Then chute tube assembly does not have to be removed. To remove the grass bags, lift up on bag and unhook the frame of the bag from the support tube assembly. To empty the grass, use the handle which is provided on the bottom of each bag. NOTE: Units with twin cylinder engines (fuel tank in the rear): To allow access to the fuel tank, disconnect the lower chute tube from the discharge chute. Lift up on the center of the grass catcher support tube, and swing the grass catcher out of the way. IMPORTANT: Under normal usage, the grass collector is subject to wear and should be checked periodically. Be certain any replacement bag complies with the mower manufacturer’s recommendation. Wash grass bag periodically with water. Allow to dry thoroughly in the shade. Do not use heat. N 7 Models 063 and 103 7 PARTS LIST FOR MODELS 063 AND 103 GRASS COLLECTORS REF. NO. PART NO. CODE DESCRIPTION REF. NO. PART NO. CODE DESCRIPTION 1 728-0123 Pop Rivet .188 Dia. 28 736-0253 Bell-Wash. .505" I.D. x 1.0" O.D. 2 710-0281 Hex Bolt 1/4-28 x .88" 31 16594A Grass Catcher Cover Ass’y. (063) 3 712-0272 Hex Sems Nut #10-24 Thd. 631-0007 Grass Catcher Cover Ass’y. (103) 4 712-0138 Hex Nut 1/4-28 Thd.* 32 726-0258 Twist Fastener 5 736-0329 L-Wash. 1/4" I.D.* 33 16847A Screen Ass’y. 6 749-0701 Catcher Bag Frame 34 16596 Hinge Brkt. Ass’y. 7 764-0221 Grass Catcher Bag 35 710-0776A Hex AB-Tap Scr. 1/4X.62" 8 712-0287 Hex Nut 1/4-20 Thd.* 36 723-0412 Seal—7" (063) 10 736-0400 Flat Wash. 1/4" I.D. 723-0413 Seal—8" (103) 15 16587B Catcher Support Tube Mtg. Brkt. 37 710-0351 Truss B-Tap Scr. #10 x .5" Lg. 16 16592 Catcher Support Tube Ass’y. 38 731-0824A Plastic Plate 18 16593A Catcher Latch and Support Brkt. 39 726-0244 Speed Nut 19 16611C Grass Catcher Suppoit Brkt.— 47 710-0258 Hex Bolt 1/4-20 x .625"* R.H. 49 712-0324 Hex Ins. L-Nut 1/4-20 Thd. 20 16610C Grass Catcher Suppôt t Brkt.— 50 723-0383 Retainer Strap Ass’y. L.H. 52 731-0899 Catcher Tube (063) 21 710-0118 Hex Bolt 5/16-18 x .7...
Este manual também é adequado para os modelos :Gazonouborschiki - 190-063-000 (834.42 kb)