Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Remove the hand knobs and cupped washers from each side of the discharge opening on the left side of the shredder. 2. Remove the hex lock nut, two spacers and hex bolt from inside the hinge on the chute deflector. Do not remove one spacer from the hex bolt. Place the chute deflector in position on the discharge opening on the left side of the shredder. Insert hex bolt and spacer through hinge on chute deflector and housing (spacer fits inside of hinge). Place the second spacer over the hex bolt, inside the other part of the hinge. Secure with hex lock nut. Tighten securely. Secure both sides of the chute deflector to the housing using the hand knobs and cupped washers (cupped side of washers go against the chute deflector). WARNING: Do not operate this chipper-shredder unless the chute deflector has been properly installed and is secured with the hand knobs. 3. 4. 5. A FIGURE 3. Hopper Self-Tapping Screws FIGURE 4. N -ATTACHING THE LOWER LEAF RAMP SECTION (Hardware A) Insert hex bolt 8-3/8" long through lower leaf ramp section and frame. Secure with flat washer 5/16" I.D. and hex lock nut. Make certain the edges of the lower leaf ramp section are underneath the stop washers. See figure 3. Plastic insert in hex nut should face away from lower leaf ramp section. Tighten hex nut until parts are snug, but so lower leaf ramp section can still be rotated on the frame. ATTACHING THE HOPPER When attaching the hopper, first remove the five selftapping screws from the frame of the unit. Place the -hopper in position on the shredder. See figure 4. Start all five self-tapping screws, then tighten securely using a 1/2" socket wrench. ATTACHING THE UPPER LEAF RAMP SECTION (Hardware B) Place the edge of upper leaf ramp section inside the lower leaf ramp section. Secure with four truss machine screws and hex lock nuts. The heads of the truss machine screws should be to the inside of the upper leaf ramp section. Start all screws and nuts, -then tighten securely. See figure 5. 4 ATTACHING THE CATCHER BAG Your shredder is equipped with a catcher bag to catch the shredded material. To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the drawstring, pull on the drawstring until the bag is tight around the chute opening. Release plunger to lock it into position. "♦“See figure 6. FIGURE 6. OPERATION KNOW YOUR SHREDDER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SHREDDER. Compare the illustrations with your shredder to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Hopper Chipper Chute Spark Plug Choke Lever Throttle Control Starter Handle FIGURE 7.—Model 645 Shown OPERATING CONTROLS (See figure 7) RELEASE BAR—Used to release the leaf ramp when raising or lowering. CHOKE LEVER—Used to enrich the fuel mixture in the carburetor when starting a cold engine. STARTER HANDLE—Used to manually start the engine. THROTTLE CONTROL—Controls engine speed and stops the engine. The operation of any shredder can result in foreign objects being thrown into the eyes, which AgQiQggn can result in severe eye damage. F/lAFirv^GuissE^ Always wear safety glasses or eye r sh‘e,c*s- We recommend wide vision safety mask for over spectacles or standard safety glasses. 5 I BEFORE STARTING 1. Place the shredder on a firm, level surface 2. Service engine with gasoline and oil as ins tructed in the separate engine manual packed w th your shredder. 3. Attach spark plug wire to spark plug. NOTE: Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is sh adding or chipping, it may be necessary to unclog ; he unit before it can be restarted. Refer to “Removing the Flail Screen” on page 8. TO START ENGINE A WARNING: Be sure no one other than the operator is standing near the shredder while starting or operating. 1. Place the throttle control lever in FAST position. See figure 8. 2. Move choke lever to CHOKE position (a warm engine may not require choking). 3. Tecumseh engines only: Prime engine as instructed in separate engine manual. 4. Grasp starter handle (see figure 8) and p jII rope out slowly until engine reaches start of cc impression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. 5. Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Lot rope rewind slowly. Do not let starter handle sn< ip back against starter. 6. Repeat preceding instructions 4 and 5 until engine fires. When engine starts, move choke lever on engine halfway between CHOKE and RUN. FIGURE 8.—Model 645 Shown 7. Move throttle control to IDLE position fo' a few minutes warm-up. Move choke lever to RL N position as engine warms up. NOTE: In order to idle smoothly, a new engi ne may require 3 to 5 minutes run...
Este manual também é adequado para os modelos :Jardim Shredders - 242-645-000 (2.15 mb)
Jardim Shredders - 242-648-000 (2.15 mb)
Jardim Shredders - 242A648-000 (2.15 mb)