Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
It is suggested that this procedure be performed by your nearest authorized dealer. CARBURETOR ADJUSTMENT A WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of heated surfaces and muffler. Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. NOTE: A DIRTY AIR CLEANER WILL CAUSE ENGINE TO RUN ROUGH. BE CERTAIN AIR CLEANER IS CLEAN AND ATTACHED TO THE CARBURETOR BEFORE ADJUSTING CARBURETOR. Do not make unnecessary adjustments. Factory settings are satisfactory for most applications and conditions. If adjustment is needed, refer to the separate engine manual packed with your shredder. OFF-SEASON STORAGE The following steps should be taken to prepare your shredder for storage. 1. Clean and lubricate the shredder thoroughly as described in the lubrication instructions. 2. Refer to engine manual for correct engine storage instructions. 3. If storing in an unventilated or metal storage shed, coat metal parts with a light oil or silicone to prevent rust. 4. Store in a dry, clean area. Do not store next to corrosive materials, such as fertilizer. 9 Models 645 and 648 NOTE This instruction manual covers various models, and all specifications shown do not necessarily apply to your model. Specifications subject to change without notice or obligation. 19 Models 645 and 648 PARTS LIST FOR MODELS 645 and 648 SHREDDERS \ EF. 40. PART NO. CODE DESCRIPTION REF. NO. PART NO. CODE DESCRIPTION 1 742-0571 N 37 710-0157 Hex Bolt 5/16-24 x .75" Lg. 13431 38 736-0119 L-Wash. 5/16" I.D.* 2 710-0818 Hex Patch Bolt 3/8-24 x 2" Lg. (Gr. 8) 39 710-3008 Hex Bolt 5/16-18 x .75" Lg. (Gr. 5) 3 714-0114 Sq. Key 1/4 x 2.0" Lg. 40 710-0380 Hex Bolt 5/16-18 x 1.75" Lg.* 4 736-0217 L-Wash. 3/8" I.D. H.D. 41 681-0004 N Flail Housing Ass’y-—L.H. 5 736-0247 FI-Wash. .406" I.D. x 1.25" O.D. Hdn. 42 43 781-0474A 735-0639 N Flail Housing Ass’y.—R.H. Spark Plug Boot (Optional) 6 11459B Flail 44 — Engine 7 711-0564 Flail Spacer 45 747-0531A Release Bar 8 711-0833A Clevis Pin .496" Dia. 46 732-0546 Torsion Spring 1.06" Lg. 9 711-0834 Flail Spacer w/. 160" Dia. Hole 47 712-0429 Elastic Lock Nut 5/16-18 Thd. 10 715-0249 Spring Roll Pin 1.12" Lg. 48 710-0601 Hex Wash. Hd. Self-Tap Scr. 11 736-0192 H^igh^m-D. x .94" O.D. 5/16-18 x .75" Lg. 12 681-0002 N 49 11480 Stop Washer 781-0484 Impeller Ass^Tt 50 736-0264 FI-Wash. 5/16" I.D. 13 781-0490 Chipper Blade 51 710-0542 Hex Bolt 5/16-18x8.38" Lg. 14 710-1054 Flat Hd. Scr. 5/16-24 x.75" Lg. 52 781-0487B N Back-Up Plate 15 712-0411 Hex Top L-Nut 5/16-24 (Gr. 5) 53 16522B N/638 Inlet Guide Ass’y. 16 736-0119 L-Wash. 5/16" I.D.* 54 11481B 638 Hopper Ass’y. 17 710-0825 Hex Bolt 1/4-20x3.75" Lg.* 55 781-0509 638 Lower Leaf Ramp Section 18 736-0142 FI-Wash. .281" I.D. x .5" O.D. 56 710-0286 Truss Mach. Scr. 1/4-20 x .5"* 19 750-0793 Chute Hinge Spacer 1.66" Lg. 57 712-0107 Hex L-Nut 1/4-20 Thd. 20 711-0835 Clevis Pin .5" Dia. x 4.62" Lg. 58 11461B 638 Upper Leaf Ramp Section 22 712-0291 Hex Ctr. L-Nut 1/4-20 Thd.* 59 726-0214 Push Cap 5/8" Dia. Rod 23 714-3010 Cotter Pin 3/32" x 5/8" 60 736-0187 FI-Wash. .64" I.D. x 1.24" hy24 781-0457 Shredder Screen 61 750-0786 Spacer .64" I.D. x .38" Lg. '">5 714-0145 Internal Cotter Pin 3/8" Dia. 62 738-0814 ^^der Axle (645) ¿6 781-0480 Chute Deflector Ass’y. 738-0813 iShredder Axle (648) 27 712-3010 Hex Nut 5/16-18 Thd. (Gr. 5) 63 734-1600 28 736-0242 Bell-Wash. .345" I.D. x .88" 734-1597 29 720-0170 Hand Knob 734-1598 30 31 747-0744A 732-0542 Chipper Door Rod Torsion Spring 1.14" Lg. 64 65 734-1455 741-0487 plangeifeacirig .632" I.D. (648) 32 781-0489 Chipper Door 66 734-0255 33 781-0475 Chipper Chute Ass’y. 67 737-0280 34 736-0170 Spec. L-Wash. 5/16" I.D. — 764-0199A Bag (tëotShown)^ 35 712-3010 Hex Nut 5/16-18 Thd. (Gr. 5) — 723-0400 Safety Glasses (Not Shown) 36 781-0510 638 Shredder Frame f'fModels 242-645 and 242-648 only. *For faster service obtain standard nuts, bolts and washers locally. If these items cannot be obtained locally, order by part number and size as shown on parts list. NOTE: The engine is not under warranty by the shredder manufacturer. . .If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the “Yellow Pages” of your telephone book under “Engines-Gasoline.” Find It Fast In The Yellow Pages CODE: N notates a new part (not previously existing). A three digit number is the color code. Specify color code as shown below if color or finish is important when ordering parts, [i.e., 638 for Red Finish]. Color Codes 456—Radiant Tangerine 637—Black 460—Green Flake 638—Red 483—Charcoal Gray 640—Green 498—Yellow 646—CM Blue 499—Beige 657—Teal 629—Silver Flake 11 TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE(S) CORR...
Este manual também é adequado para os modelos :Jardim Shredders - 242-645-000 (2.15 mb)
Jardim Shredders - 242-648-000 (2.15 mb)
Jardim Shredders - 242A645-000 (2.15 mb)