Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Before connecting make sure that the voltage and the frequency correspond to that stated on the data plate on the oven. Place a bi-polar switch between the oven and the network accessible after installation, whose contacts have a minimum opening distance of 0.1 inches, with an appropriate input (for example, magnetothermal switch). When the oven is in operation, the power supply voltage must not vary from the value of the nominal voltage by more than ± 10%. The oven must be connected to the ground line of the network. 3.2 INSTALLATION LOCATION Make sure you have the correct power sup- ply for the oven model you have purchased. Check the technical data sheets at the back of this manual if you are in doubt. Do not install any Cadco-Unox Convection Oven directly on the floor. Cadco has oven stands to perfectly elevate your oven as well as provide pan storage. OST-34A for models OV-350 and OV-400 OST-56A for models OV-500 and OV-600 If the oven must be placed near walls, dividers, or moldings Cadco recommends they be made of non-combustible materials. Be sure to observe all safety and fire codes when positioning your convection oven. All of our convection ovens have a vapor vent in the back of the unit. When installing your convection oven, leave a space of 4” [mini- mum] between the back of the oven and the wall, and 2” minimum on the top and sides. Where applicable, ventilation hood require- ments vary according to local codes. We do not suggest using the Cadco-Unox Convection Ovens for built in applications. Measure to make sure that your new oven will fit in your available space. 3.3 REMOVE THE PROTECTIVE FILM Be sure to remove the laser film from the ENGLISH 4 ENGLISH XA030/OV-400 XA085/OV-500 XA006/OV-250 XA015/OV-350 XA090/OV-600 Use only AWG10 cords 220-230 V ~ 21354L L L2 L2 208 - 240V 208-240V WARNING: Connect the electrical cable to the terminal- board as indicated in the drawing: insert screw-wise the copper bridge and the elec- trical cable together under the screw (see diagram below.) Tighten the screw taking care that the cable and the copper bridge are well gripped under the screw. A wrong connection can cause an overheat- ing of the terminal board and burn it. Electrical connection must be a proper outlet for the 3 pronged cord. Before connecting power, make sure the voltage and frequency correspond to the data plate on the oven (120 volts/60hz.), and that your electrical cir- cuit can handle the12.5 amps used by the oven in addition to any other appliances operating on the same circuit. 4.2 WATER CONNECTION - Applies only to OV- 500 and OV-600 WATER CONNECTION TO THE NETWORK: Connect the decalcified water inlet ducts placed on the back of the oven to the specif- ic distribution network by means of a mechanical filter and a cut-off cock. Before connecting the filters, let a certain quantity of water flow to clean the duct from any ferrous slag. The water must have a hardness between 0.5°-5°F (this in order to reduce the formation of limestone deposits inside the electro-valve and inside the cooking cham- ber) and a pressure value between 0.5-2 bar (7.25 – 30 psi.) Due to variations in water composition in different areas, you may want to consider using a commercial water filter. 4.3 MAINTENANCE Before carrying out any type of maintenance it is necessary to disconnect the electrical power supply and wait for the oven to cool down. ENGLISH 5ENGLISH OV-600 ONLY MAX 2 bar (30 psi) (7.25 – 30 psi.) Due to variations in water composition in different areas, you may want to consider using a commercial water filter. 4.3 MAINTENANCE Before carrying out any type of maintenance it is necessary to disconnect the electrical power supply and wait for the oven to cool down. ENGLISH 5ENGLISH OV-600 ONLY MAX 2 bar (30 psi) ENGLISH ENGLISH II. INSTRUCTIONS FOR THE USER 1. “BURN IN” OVEN BEFORE FIRST USE Before you start cooking with your new Cadco-Unox Convection Oven you will want to “burn in” the oven. This simple procedure will get the new oven smell out of your oven and off your food. -Clean the oven with a mild detergent inside and out. -Turn the temperature control dial to 400F. -Set the timer for 30 minutes and you’ll be ready to start cooking at the end of the cycle. 2. FEATURES AND CONTROLS 2.1 PREHEAT INDICATOR LIGHT The preheat indicator light will be illuminated when there is heat being added to the cooking chamber. The preheat indicator light will be illuminated periodically throughout the cooking cycle as the oven controls call for more heat. 2.2 TEMPERATURE CONTROL Cadco-Unox temperature controls are extremely accurate. The dial will be turned clockwise and used to set your oven cooking temperature in a range 175F to 500F degrees. 2.3 TIMER DIAL Turning the timer dial clockwise allows you to set the cooking time for up to 120 minutes. When the dial is turned counterclockwise you are in manual mode with infinite cooking time. 3. SPECIAL CADCO-UNOX OVEN FEATURES 3.1 “END OF CYCLE” ALARM TONE All Cad...
Este manual também é adequado para os modelos :Fornos Elétricos - OV-250 (465.08 kb)
Fornos Elétricos - OV-500 (465.08 kb)
Fornos Elétricos - OV-600 (465.08 kb)