Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Seat the e-ring by pressing the pliers closed. 6. Repeat step 3 through 5 to secure second wheel. 7. Remove the temporary blocks. 8. Attach the vibration mounts to the support leg with 30mm capscrews and lock nuts. 9. To aid support leg assembly, rest generator on cradle, engine end down. Remove the existing hardware from the left unit vibration mount with 13mm wrench. Use the same hardware to attach the support leg. 10. Attach the other side of the support leg with a 20mm cap screw and lock nut. Rest generator on wheels and support leg. Support Leg Hex Nut Axle Flat Washer Cap Screw Handle Assembly Hex Nut Wheel E-Ring Figure 1 — Install Wheel Kit Cap Screw Hex Nut Cap Screw Vibration Mount Use existing hardware to attach left side of support leg to unit Portable Generator 6 11. If equipped, center the handle bracket on generator frame at support leg end of cradle, as shown. 12. Attach handle bracket with two M8 x 45mm cap screws and two locking hex nuts. 13. Check that all fasteners are tight and the tires are inflated to the value marked on the tire or within 15 and 40 psi. Install the 8” Wheel Kit as Follows 1. Place bottom of generator cradle on a flat surface. 2. Place axle stud through wheel retainer on cradle frame, as shown in Figure 2. 3. Use 15/16” wrench to secure the axle stud to frame with 5/8-18 jam nut. 4. Install the other axle stud in the same manner. NOTE: Be sure to install wheel with raised hub inboard. 5. Tip unit and install the wheel. Place flat washer over axle stud. 6. Retain wheel on axle stud with retaining pin. Install other wheel on remaining axle shaft the same way. 7. Attach the vibration mount to the mounting leg with a capscrew and lock nut. 8. Remove two front nuts from vibration mount on unit with 13mm wrench. Use these nuts to retain the mounting leg. 9. Center the lifting handle on generator end of cradle. Attach handle using two 13mm wrenches with two capscrews and two hex nuts. Capscrew Handle Grip Nut Mounting Leg Use Existing Fasteners to Secure Leg Jam Nut Retaining Pin Wheel Washer Axle Stud Figure 2 — Installing the Wheel Kit Capscrew Vibration Mount Nut Portable Generator Portable Generator ELECTRIC START Your unit may be equipped with electric start capability but can be started manually. If you choose not to use the electric start feature, you do not need to install the battery. If your unit does not have electric start, ignore this section. Check Battery / Attach Negative Battery Wire The sealed battery on the generator is fully charged and pre–installed except for the negative (black) battery cable. To install: 1. Cut off tie wrap securing loose end of negative (black) cable. 2. Remove nut and washer on negative battery terminal. 3. Slide negative battery cable over screw on negative terminal (Figure 3). 4. Reattach washer and nut and tighten. 5. Verify that connections to battery and generator are tight and secure. Figure 3 — Negative Battery Connection Positive battery cable Screw Negative battery cable Washer Nut BEFORE STARTING THE ENGINE Add Engine Oil and Fuel • Place generator on a level surface. CAUTION Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure. • Refer to engine manual for oil and fuel fill information. • Damage to equipment resulting from failure to follow this instruction will void warranty. • Refer to engine owner’s manual and follow oil and fuel recommendations and instructions. NOTE: Check oil often during engine break–in. Refer to engine owner’s manual for recommendations. NOTE: The generator assembly rotates on a prelubricated and sealed ball bearing that requires no additional lubrication for the life of the bearing. 7 USING THE GENERATOR System Ground The generator has a system ground that connects the generator frame components to the ground terminals on the AC output receptacles.The system ground is connected to the AC neutral wire (the neutral is bonded to the generator frame). Special Requirements There may be Federal or State Occupational Safety and Health Administration (OSHA) regulations, local codes, or ordinances that apply to the intended use of the generator. Please consult a qualified electrician, electrical inspector, or the local agency having jurisdiction. • In some areas, generators are required to be registered with local utility companies. • If the generator is used at a construction site, there may be additional regulations which must be observed. Connecting to a Building’s Electrical System Connections for standby power to a building’s electrical system must be made by a qualified electrician.The connection must isolate the generator power from utility power, and must comply with all applicable laws and electrical codes. DANGER Generator produces powerful voltage. Failure to isolate generator from power utility can result in death or injury to electric utility workers due to backfeed of electrical energy. • When using generator fo...
Este manual também é adequado para os modelos :Electricidade - 01653 (1.35 mb)