Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Raise and lower the telescopic sections and/or swivel to desired position and then push in clamp levers to secure. DO NOT over tighten tension knobs. There should only be a moderate amount of tension to maintain the telescopic position of your heater. CAUTION! Step 1 Before turning on your Infrared Heating System, check to make sure the “On/Off” switch located on the tilt switch (black box) of the head unit is pulled OUT or in the ON position (note: to turn the heater “Off”, push in the switch). Next, extend all 3 telescopic sections to their maximum extended length. Release clamp levers and pull up on each of the sectional steel tubes until each tube stops. Then push in clamp levers to secure sections in place. Adjust the tension knobs as needed to maintain height position. Step 2 The Infrared Heating System comes equipped with a heavy duty, 16/3 gauge wire and grounded plug. This appliance must be used with an outlet that has been installed and grounded in accordance with local codes and ordinances. Make sure the heater is connected to an outlet having the same configuration as shown in the figure shown to the right. DO NOT use an adapter with this product. Check with a licensed electrician if the grounding instructions are not understood completely or if the wall outlet does not match the plug. Step 3 Your Mojave Sun, Infrared Heating System is ready to enjoy. Plug the appliance in and enjoy the warmth! 9 Specifications Model: 02117/60694/02678 Voltage: 120 volts Amps: 12.5 amps Wattage: 1500 watts Lamp Type: Quartz Halogen Minimum Operational Height: 8 ft., 2 in. (98 in.) Assembled Weight: 53 lbs. Head Unit Dimensions: 4.5” x 7” x 22” Heater Assembled Dimensions: 22” diameter base, 98” height Storage * Always UNPLUG the unit when not in use. * Once the head unit has completely cooled, store the heater with the protective vinyl cover on the head unit. * When heater is not in use for an extended period of time, store in a covered location that is dry and out of the weather. Make sure the heater is stored in a location that is out of the way of people and pets that may accidentally knock the heater over or damage the appliance. Before storing the heater, make sure the electrical cord is coiled and out of the way. * When storing, ALWAYS lower the telescopic pole to its lowest level. This will make it easier to store and reduce the risk of any accidental tipping over of the heater. Maintenance Your Infrared Heating System is virtually maintenance free! A minute to wipe down exposed surfaces is all it takes to maintain your heater. * Head unit and shield: Use a non-abrasive cleaner and a soft cloth to wipe off debris and dirt from the exposed surfaces. NEVER spray liquids or cleaners into the housing area where the halogen lamp is located. Do not try to disassemble of clean the inner cavity where the halogen lamp is located. For any maintenance on the head unit, please call the toll free customer service hotline. * Telescopic pole and curved arm components: These can easily be wiped clean using a non-abrasive cleaner and a soft cloth. * Base with wheel assembly: Use non-abrasive cleaner and a soft cloth. Any scratches, chips or rust spots can be touched up using an exterior matte finish black paint. 10 Halogen Lamp Replacement Contact the toll free customer hotline to order approved replacement lamps and parts. Use ONLY approved original equipment and replacement halogen lamps to ensure safe, proper and maximum output operation of your heater. NOTE: Do NOT touch the new halogen lamp with your bare fingers. Oils from your hand could reduce the life of the lamp by causing a heat spot. We recommend using clean cotton or plastic gloves to handle the lamp. A clean paper towel will also work. MAKE SURE THE HEATER IS TURNED OFF AND DISCONNECTED FROM THE ELECTRICAL OUTLET BEFORE YOU BEGIN!!!! TO REPLACE THE HALOGEN LAMP: 1. Be sure the heater is unplugged from the wall outlet. Remove the head unit assembly from the telescopic pole. 2. Remove 8 screws from each end of the head unit and pull off end plates (#2). Note the placement of the 2 small sheet metal screws on each end plate. Also note end plate side with beveled holes faces outward when re-assembled. 3. Pull out and remove the left and right front air vent panels and protective wire grill (#3). Note the position of end clips on vent panel. They must be aligned as close to the end connectors of lamp tube as possible when re-assembled. Pull or push into place as needed. DO NOT allow metal parts to touch the actual lamp tube when re-assembled. 4. Gently pull out entire old lamp assembly from the clips at the terminal connection ends (#4 & 5). Slide and lift the connection ends out from the friction clips by gently pushing apart the clips. Unscrew wire leads from terminal. Remove entire old lamp assembly. 5. Using gloves, gently re-insert connection ends of the NEW lamp assembly into the friction clips (#4). Pull apart the clips slightly and gently push the connect...
Este manual também é adequado para os modelos :Eléctrico - 02117 (580.57 kb)
Eléctrico - 60694 (580.57 kb)