Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
DO NOT DEFEAT THE SAFETY PURPOSE OF THE POLARIZED PLUG. Tip-Over Safety Switch This heater equipped with tip-over safety switch located underneath the base of the heater. This switch must be pressed inward for the heater to function properly. Some soft surfaces such as carpet may not be able to fully press in this switch. For some soft surfaces, a hard flat object will need to be placed underneath the heater for it to function properly. PLEASE DO NOT TAPE OR GLUE THIS SWITCH. SAFETY SWITCH BOTTOM OF THE HEATER PRODUCT DIAGRAM Operating Knob Carry Handle (on back) Reflective Halogen Tubes Base Tip-over Safety Switch (on bottom) ASSEMBLY Remove the heater body and base from box. Remove the packaging materials. 1. Lay the heater body on a level surface, and then unscrew the 2 butterfly screws from the bottom of the heater. 2. Pull the power cord through the hole at the center of the base, and align the base with the bottom of the heater. The power cord should fit through the slot in the base. 3. Attach the base to the heater body with the butterfly screws. OPERATING INSTRUCTIONS Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet. Turn the knob located on top to the desired setting: OPERATING THE HEATER: • LOW: Both reflective tubes operate, heating up to 400W. • HIGH: Both reflective tubes operate, heating up to 800W. • LOW SWING: The unit will oscillate 60° on low power mode. • HIGH SWING: The unit will oscillate 60° on high power mode. • OFF: Heater will stop operating. • Unplug the heater when not in use NOTE: A tip-over safety protection switch is installed at the bottom of the heater. When the heater is not placed horizontally, laid down or lifted up, it stops operating to ensure safety. After placing it upright the heater will resume operation. (See Page 4 for more information). NOTE: For safety, if the heater’s internal temperature rises above a certain point, the heater is designed to automatically shut off. To restart the heater in this situation: 1. Turn the Operating Knob to OFF. 2. Unplug the power cord from the outlet and allow the heater to cool for at least 10 minutes. 3. Plug the power cord back into the outlet. Turn the knobs located on top to select the desired setting. WARNING: It is normal for the power cord to feel warm to the touch; however, a loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for damage. MAINTENANCE 1. Unplug the unit and let it cool completely. 2. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. CAUTION: DO NOT let liquid enter the heater. 3. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater. 4. DO NOT immerse the heater in water. 5. Wait until the unit is completely dry before use. STORAGE Store the heater in a cool, dry location when not in use. Preferably, to prevent dust and dirt build-up, use the old packaging to repack the unit. TROUBLESHOOTING If the heater will not operate, please check the following before seeking repair of service: 1. Check if the power cord is plugged into an electrical outlet, if not, plug in. 2. Check if electricity to the main fuse is working. 3. Check if the Power Knob is turned to Low or High. If not, turn the Power Knob to one of these settings. 4. Check if the heater is on a level surface. If the tip-over safety switch is not pushed in, the heater will not run. WARRANTY One Year Limited Warranty Soleus International Inc. warrants the accompanying Soleus Air heater to be free of defects in material and workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the date of original retail purchase in the United States. If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of charge within a reasonable time after the unit is returned during the warranty period. As a condition to any warranty service obligation, the consumer must present this Warranty Certificate along with a copy of the original purchase invoice. THIS WARRANTY DOES NOT COVER: • Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in material or workmanship. • Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions in the instructions. • Damage to the finish of the case, or other appearance parts caused by wear. • Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus International Inc. • Freight and Insurance cost for the warranty service. ALL WARRANTIES, INCLUDING ANY IMPLIED WA...
Este manual também é adequado para os modelos :Eléctrico - 3077997 (701.17 kb)