Assessments - 3, GPA: 4.7 ( )

Fabricante : Monessen Hearth Arquivo Tamanho: 2.28 mb Arquivo Nome : Língua de Ensino:

MILLI-VOLT AND THERMOSTAT CONTROL LIGHTING INSTRUCTIONS 58D56002 23 OPERATING INSTRUCTIONS AND CLEANING AND SERVICING MATCH LIGHTING INSTRUCTIONS 1. Open stove door. Remove any items necessary for easy access to the pilot (for example: logs, screens, etc.). 2. Follow appropriate lighting instructions found previously. Light a match and hold the flame to the end of the pilot and ignite the pilot. 3. After control knob has been released and pilot stays lit, reinstall any items that were removed for pilot access. Close and latch stove door. 4. Replace ignitor battery. If ignitor still does not work, then call a qualified service technician for repair or replacement of the piezo ignitor. CLEANING AND SERVICING Annual inspection and cleaning by your dealer or qualified service technician is recommended to prevent malfunction and/or sooting. WARNING Turn off heater and allow to cool before cleaning. Disconnect electrical power before cleaning or servicing. Remove logs, handling carefully by holding gently at each end. Gloves are recommended to prevent skin irritation from ceramic fibers. If skin becomes irritated, wash gently with soap and water. Refer to manual for correct log placement. PERIODIC CLEANING - See parts diagram for location of items discussed below. • Do not use cleaning fluid to clean logs or any part of heater. • Brush logs with soft bristle brush or vacuum with brush attachment. • Vacuum loose particles and dust from the front and rear burners, control and piezo covers and grate weldment. • Inspect and clean burner air intake holes. Remove lint or particles with vacuum, brush, or pipe cleaners. Failure to keep air intake holes clean will result in sooting and poor combustion. • External case should be dusted and wiped with a moist cloth. ANNUAL CLEANING/INSPECTION - Refer to parts diagram for location of items discussed below. • Inspect and clean burner air intake holes. Remove lint or particles with vacuum, brush or pipe cleaners. Failure to keep air intake holes clean will result in sooting and poor combustion. • Inspect and clean all burner ports. • Inspect ODS pilot for operation and accumulation of lint at air intake holes. • Verify flame pattern and log placement for proper operation. • Verify smooth and responsive ignition of main burner and rear burner. • Replace AA battery in ignition module. 24 58D6002 LOGS 12345REPLACEMENT PARTS ARE AVAILABLE THROUGH YOUR RETAILER. Item Description Qty 1 Back Log 1 58D1901 2 Bottom Left Log 1 58D1902 3 Bottom Right Log 1 58D1903 4 Left Top Log 1 58D1904 5 Right Top Log 1 58D1905 REPLACEMENT PARTS LIST Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal WARNING injury. 58D56002 25 REPLACEMENT PARTS BURNER ASSEMBLY 8 7 14 12 approved with this appliance may result in property damage or personal injury. 12345691011131516Failure to position the parts in accordance with these diagrams or failure to use only parts specifically WARNING 26 58D6002 REPLACEMENT PARTS LIST REPLACEMENT PARTS ARE AVAILABLE THROUGH YOUR RETAILER. BURNER ASSEMBLY Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Description Piezo Ignition Module Piezo Switch Piezo Wire Front Burner Rear Burner Control Valve Front Burner Injector Rear Burner Injector ODS Pilot Assembly On/Off Control Knob Hi/Lo Control Knob On/Off Switch VF Valve Tube VF Rear Burner Tube VF Front Burner Tube 5/16 Union Tee CSVF20 CSVF30 Qty Natural Propane Natural Propane 1 45D0077 45D0077 45D0077 45D0077 1 1 1 1 45D0078 00K0632 33D0070 — 45D0078 00K0632 33D0071 — 45D0078 00K0632 58D0193 58D0435 45D0078 00K0632 58D0193 58D0435 1 1 1 1 14D0467 — — 14D0473 14D0468 — — 14D0474 14D0467 58D0061 58D0061 14D0473 14D0468 58D0056 62D3005 14D0474 1 1 1 1 43D0094 43D0095 32D0232 — 43D0094 43D0095 32D0232 — 43D0094 43D0095 32D0232 58D0427 43D0094 43D0095 32D0232 58D0427 1 1 1 — — — — — — 58D0428 58D0429 43D0181 58D0428 58D0429 43D0181 Accessories Flex Connector Wall Switch Kit Wall Thermostat Kit Hand Held Remote Hand Held Thermostat Remote Thermostat Control Sensor Flexcon 30 MVWS MVWTS RCM RCT TS 58D56002 27 TROUBLESHOOTING WARNING Turn appliance OFF and allow to cool before servicing. Only a qualified service person should service and repair the heater. Note: All troubleshooting items are listed in order of operation. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY When ignitor button is pressed, there is no spark at ODS/pilot. 1. Ignitor electrode positioned wrong. 2. Ignitor electrode is broken. 3. Ignitor electrode not connected to ignitor cable. 4. Ignitor cable pinched or wet. Keep ignitor cable dry. 5. Broken ignitor cable. 6. Bad piezo ignitor. 7. No battery power (auto spark). 1 Replace ignitor. 2. Replace ignitor. 3. Reconnect ignitor cable. 4. Free ignitor cable if pinched by any metal or tubing. 5. Replace ignitor cable. 6. Replace piezo ignitor. 7. Replace battery. Appliance produces unwanted 1. Appliance ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :