To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel. SPECIAL ATTENTION: The use of an extension cord is not recommended. However, if it is absolutely necessary, be sure that the cord is (1) No. 14 AWG minimum size and rated no less than 1875 watts; (2) UL Listed; (3) as short as possible (long cords can overheat, as well as trip circuit breakers); (4) not use

or 4 hr. setting to select how long you’d like heater to stay on. The unit will shut off automatically once the selected time runs out. To operate heater continuously, turn timer knob to ON. Remember to shut unit Off when done. 6. To use as a fan without heat, move control knob to FAN ONLY and thermostat control toward HOT until fan begins to operate. No heating will occur in this mode. 7. To turn off, turn thermostat control to FROST WATCH and control knob to Off. Note: The power indicator ligh

Thermostat switch 3. Power indicator light 8. Base 4. Power settings (fan, low, high) 5. Cool-touch rear handle 6. Fan only setting 7. Front/back grilles 9. Tip-over switch (under unit) Note: If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. How to Use This appliance is intended for household use only. The Advanced Safety Technology™ (AST) system features unique technology built into y

Note: If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. 2 How to Use This appliance is intended for household use only. Important: For warranty verification, do not remove line cord sticker. The Advanced Safety Technology™ (AST) system features unique technology built into your heater that offers protection detailed in the "Special Features" section. Included in AST is a shock protection d

Plug heater into a standard AC outlet. Caution: Be sure that no other appliances are plugged into same circuit with heater as a circuit overload could occur. 2. Press ON/OFF button to activate heater. The red lights by POWER and TEMP SETTING buttons will turn on (B). 3. Press POWER button to select appropriate setting: LO for a x 3m), MED for a medium (approx. 12’x12’/3.8m x 3.8m), room (approx. 12’x 16’/3.8m x 5m). 4. Press TEMP SETTING button to MAX. Once desired room temperature lower tempera

VEUILLEZ LIRE ET CONSERVER CE GUIDE D’ENTRETIEN ET D’UTILISATION. Digital 9-fin oil-filled heater Calentador de aceite con 9 aletas y digital Radiateur a l’huile, a 9 ailettes et a affichage numerique ? USA/Canada 1-800-231-9786 Mexico 01-800-714-2503 Accessories/Parts (USA/Canada) 1-800-738-0245 Accesorios/Partes (EE.UU/Canada) Accessoires/Pieces (E.-U./Canada) Models/Modelos/BDOH200 BDOH200C BDOH200.Pub179200RV2 5/18/05 9:11 AM Page 2 IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk o

It contains no user serviceable parts. Refer service to qualified service personnel. 1. Always turn the unit Off, unplug, disconnect the cord from the outlet, and allow the heater to cool completely before cleaning. To clean the exterior, use a soft dry cloth or one moistened with a mild detergent to wipe the outside surfaces. Do not use abrasives or harsh cleansers. Dry surfaces thoroughly before using the heater. Or, you can use a vacuum with a dusting brush attachment to clean away dust. 2. P

No heating will occur in this mode. 4. For models with the Oscillating feature, slide the lever on the base of the unit to “Oscillation On” (C). 5. For models with a built-in Digital Thermometer, consult the thermometer to see the area temperature. Depending on the model, it will be displayed in either °F or °C (D). The digital thermometer runs on batteries and is not affected by whether or not the unit is plugged in. The batteries are already installed. To activate the thermometer, turn the uni

Repeat for the other wheel then repeat the process to assemble the other wheel support. • Place the heater on the floor upside down. It is quite normal to hear the oil moving inside the radiator. • Holding the bent end, insert the wheel clamp (7) between the last 2 heating fins. Place one assembled wheel support over this, & fit the bent end of the clamp through the hole in the support. • Slide the wheel support towards the bend in the wheel clamp, rotating the clamp as it moves until the free e

Readjust your temperature or room settings. If unit fails to operate after 10 minutes, it may mean heater has internal damage and thermal fuse has been tripped so heater can no longer operate. 2. Motion-off detection feature: Cuts the power if unit falls over in any direction or is lifted (such as if you move it to another part of the room). 3. Tip-over switch: Cuts the power if unit is knocked over forward or backward. Both are controlled by the tipover switch on bottom of unit. Do not attempt