Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
This Royal Cozy Fires Inset Live Fuel Effect gas fire has been developed to give a realistic coal burning appearance with the instant control and convenience of gas. The fire has been constructed to enable it to be installed into most applications where the warmth and comfort of an open fire with high radiant and convection heat is required. The coal bed uses ceramic simulated ‘coals’ and is to give a realistic appearance and to allow secondary air to be entrained into the bed to ensure clean combustion. An aerated twin ported steel burner is used, running parallel across the front of the fire combined with a single gas control with a variable high / low setting. This is fitted with a Flame Supervision Device (FSD) to ensure that should the pilot flame be extinguished for any reason, (including turning off the appliance), the gas supply to the burner is cut off until a full lighting sequence is repeated. A separate Piezo igniter is used to ignite an oxy-pilot sensor (ODS), this will cause the appliance to ‘shut off’ in the event of the flame extinguishing and also in the event of continued spillage occurring under hazardous or blocked flue conditions. The fire bed consists of ceramic fibre components and coals, all are removable for cleaning purposes when required. It is important when relaying the coal bed and coals to follow the instructions correctly. . This appliance has been designed and manufactured to the requirements of the British Standards Institution BS 5258 Part 16 1990 and is for use on Natural Gas Only. All gas appliances must be installed by a competent person in accordance with the current Gas Safety (Installation and Use) Regulations 1994 (as amended) or the rules in force and in accordance with the manufacturers instructions, failure to do so could lead to prosecution. The chimney or flue (unless new) must be swept before installation. It is recommended that the appliance is serviced annually by a competent person and the flue checked for satisfactory clearance of products and that there is no excessive build up of soot. The curing effect of heating the coals will cause an initial odour which, although not harmful, may require additional ventilation until the odour has disappeared. The appliance has a naked flame, a fireguard conforming to BS 6539 or BS 6778 should be used for the protection of the very young, elderly and infirm. Combustible materials should not be put on or left in the hearth nor should the coal bed be used to burn rubbish or other materials. Care must be taken on the selection of wall coverings within close proximity of the fire as some vinyl and embossed materials may be become discoloured by convection heat. Soft furnishings must be kept clear from the radiant heat of the fire and from impinging the hearth area. The hearth must not be covered by any combustible materials such as carpets etc. This product uses fuel effect pieces, gaskets and insulation material containing Refractory Ceramic Fibre (RCF), which are man-made vitreous silicate fibres. Excessive exposure to these materials may cause temporary irritation to eyes, skin and respiratory tract, consequently, it makes sense to take care when handling these articles to ensure that the release of dust is kept to a minimum. This fire will run for 5.4 hours on one therm of gas with the gas control on the high setting. . 1. Remove the fret by lifting upwards (controls cover). 2. Press and turn the gas control until the indicator mark is opposite to IGN keeping the control fully depressed. Press and release the ignition button. Check that the pilot flame has lit at all ports. Keep the gas control depressed for a further 20 seconds. Release the gas control and check the pilot remains alight. 3. Depress the gas control slightly and turn fully anti-clockwise until the indicator is opposite the small flame symbol. The burner will now ignite from the pilot assembly and run at the low rate. Page 2 4. Depress the gas control slightly and turn clockwise until the indicator mark is opposite to the large flame symbol. The burner will now run at its maximum rate. 5. To turn the appliance ‘off’, return the control to the ‘off’ position. 6. If for any reason the fire cuts out, return the control knob to the ‘off’ position and wait 3 minutes before relighting. . Allow the appliance to cool sufficiently before removing all of the coals and firebed components for cleaning purposes. Once all the ceramics are removed from the firebed check that no debris is located in the burner slots (both front and rear). If any debris is present it may easily be removed by using a small piece of thin cardboard to ease out any foreign matter. Be sure to remove the cardboard after use. Should any soot accumulation become excessive, the fuel effect pieces should be removed from the fire for cleaning. Cleaning should be carried out in a well-ventilated area or in the open air, by gently brushing with the pieces held away from your face so...