Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in (3 mm). Verify black ground wire from module wire harness is grounded to metal chassis of appliance. Verify battery voltage is at least 4 volts. Replace batteries if voltage is below 4. Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure or screen if present, or any other metal object. Verify correct pilot orifice is installed and gas inlet is set to pressure specifications. Check pilot for soot. Clean if necessary. Verify module is securely grounded to metal chassis of appliance. Verify that wire harness is firmly connected to the module. Verify that ceramic insulator around the flame sensing rod is not cracked, damaged, or loose. Verify connection from fl ame sensing rod to white sensor wire. Polish flame sensing rod with fi ne steel wool to remove any contaminants that may have accumulated on flame sensing rod. Verify continuity with a multimeter with ohms set at lowest range. Replace pilot if any damage is detected. Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire “I” from module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is fine. Shut off gas and power immediately and call a technician. Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. V • 4/12 1 1111 Maintaining and Servicing the Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance check-up at the beginning of each heating season. WARNING Risk of injury or property damage Before servicing: • Turn off gas. • Turn off electricity to appliance. • Disable remote control, if one is present. • Ensure appliance is completely cooled. After Servicing: • Replace any screen or barrier that was removed. WARNING Annual inspection by qualified technician recommended. Check: Clean: • Condition of screen doors. • Obstructions of combustion and ventilation air. • Condition of logs. • Condition of firebox. • Burner ignition and operation. • Air passageways, control compartment. • Burner, burner ports. Risk of: • Fire • Delayed ignition or explosion • Exposure to combustion fumes • Odors The logs, pilot assembly and front of appliance should be checked periodically for accumulation of soot. Clean pilot and front thoroughly with a cloth. Logs may be vacuumed gently. Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. V • 4/12 A. Maintenance and Service Tasks: Inspect Doors and surrounds Valve compartment Logs Firebox Burner ignition and operation Remote controls Maintenance Tasks 1 Inspect for scratches and nicks that can lead to rust when exposed to weather 2 Wipe face and finish material. Use a degreaser to remove soot buildup, if necessary. 1 Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided. 2 Remove any foreign objects. 3 Verify unobstructed air circulation. 1 Inspect for broken, damaged or missing logs. Replace as necessary. 2 Logs will accumulate soot. Periodically brush soot from the logs with a paint brush or vacuum. 1 Inspect for paint condition, warping, corrosion or perforation. Sand and repaint as necessary. 2 Replace appliance if firebox has been perforated. 3 Check caulking around gas line and pilot assembly and replace as necessary to prevent water infi ltrating the appliance. 1 Verify burner is properly secured to fi rebox bottom. 2 Clean off burner top, inspect for plugged ports, corrosion or deterioration. 3 Verify air shutter is clear of dust and debris. 4 Inspect orifice for soot, dirt or corrosion. 5 Verify manifold and inlet pressures. Adjust regulator as required. 6 Inspect pilot flame strength. Clean or replace orifice as necessary. 7 Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Polish with fine steel wool or replace as required. 1 Verify operation of remote. 2 Replace batteries in remote transmitters. 3 If appliance will not be used for a long period of time, verify batteries have been removed from battery back-up in IPI systems to prevent premature battery failure or leaking. Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. V • 4/12 Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. V • 4/12 31 A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3. 44 in. (1118 mm) 28-7/8 in. (734 mm) 33-3/8 in. (848 mm) 42-1/2 in. (1080 mm) 36-1/2 in. (927 mm) 15-1/2 in. (394 mm) NON-...
Este manual também é adequado para os modelos :Lareiras - CARDOG36IL (2.82 mb)
Lareiras - CARODG36I (2.82 mb)
Lareiras - CARDOG42I (2.82 mb)