Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
and Serial No. 13.1 Parts of this appliance become hot during normal use. It is recommended that a suitable fire guard be used for protection of young children and the infirm. Indeed, all parts of the appliance should be treated as a ‘working surface’ except for the control area. USER INSTRUCTIONS 7. GAZCO FLUE SURE SYSTEM 8. THE FLAME FAILURE DEVICE 9. 'RUNNING IN' 10. SERVICING 11. VENTILATION 12. INSTALLATION DETAILS 22 13. HOT SURFACES AR0390 10 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION Packing Checklist Qty Description 1 Stove 1 Flue Blanking plate 1 Flue In fill plate 1 Coal set* 1 Flame Baffle* 1 Front Coal* 1 Fixing kit containing 1 Instruction Manual 2 Wood screws 2 Rawlplugs 1 Box spanner *Packed in appliance ModelCAT. Gas Gas Type Working Pressure NOX Class Aeration Injector Gas Rate m3.h Input kW (Gross) Country High Low Small: 8541- 8517 - Clarendon I2H Naural Gas G20 20 mbar 5 o7 mm 260 0.433 4.55 Gross 2.5 Gross GB,IE P8541- P8517 - Clarendon I3+ LPG Propane G31 LPG Butane G30 37 mbar 29 mbar 5 o13 mm 120 0.173 0.131 4.60 Gross 2.5 Gross GB,IE Medium: 8542- 8518 - Clarendon 8513-8522 - Ashdon I2H Naural Gas G20 20 mbar 5 o11 mm 375 0.639 6.60 Gross 3.25 Gross GB,IE P8542-P8518 - Clarendon P8513-P8522 - Ashdon I3+ LPG Propane G31 LPG Butane G30 37 mbar 29 mbar 5 o15.5 x 2 170 0.237 0.18 6.30 Gross 3.25 Gross GB,IE Large: 8543-8519 - Clarendon I2H Naural Gas G20 20 mbar 5 o13 mm 560 0.484 8.90 Gross 4.0 Gross GB,IE P8543- P8519- Clarendon I3+ LPG Propane G31 LPG Butane G30 37 mbar 29 mbar 5 o15.5 x 2 o13.0 X 1 240 0.35 0.266 9.30 Gross 4.0 Gross GB,IE Efficiency Class II Flue Outlet Size 127 mm (5”) o Gas Inlet Connection Size 8 mm o Minimum flue specification T260/N2/O/D/1 Maximum flue temperature 180°C A B C D E F ins mm ins mm ins mm ins mm ins mm ins mm Small 17 431 231.2 589 131.2 342 16 404 5 125 Medium 253.4 654 253.4 652 163.4 427 181.4 463 5 126 31.2 90 Large 305.8 779 28 710 181.2 468 203.8 517 61.2 166 11 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 1.1 The chimney or flue system must comply with the rules in force, and must be a minimum of 127mm in diameter. (5"). 1.2 The minimum height of the flue or chimney must be 3 metres (10ft). Any horizontal flue run from the rear outlet should not exceed 100mm from the back of the appliance. 1.3 The chimney or flue must be free from any obstruction. Any damper plates should be removed or secured in the fully open position and no restrictor plates should be fitted. 1.4 The chimney should be swept prior to the installation of the appliance, but where it can be seen that the chimney is clean and unobstructed throughout its entire length, it need not be swept. NOTE: If it is intended to fit the stove into an existing brickbuilt chimney without a closure plate*, a 5" (127mm) liner must be used. Larger lined flues may work, but in some instances could cause cold start flue problems resulting in nuisance shutdown. Lined flues above 7" (175mm) are not recommended. Due to recent changes to European chimney standards, new flues and chimneys are now described by their temperature, pressure and resistance to corrosion, condensation and fire. To assist in identifying the correct flue system, the minimum flue specification is shown in the Technical Specification in this manual. Existing chimneys are not covered by this system. 1.5 *Closure Plate Installation Small and Medium stoves can be installed into a Standard, fireplace opening with the optional closure plate and spigot extension made for the appliance. Note the stove and plate will require removing, when carrying out the annual service. The small Marlborough stove is also approved with a Closure plate for installation into pre-cast letterbox flues conforming to BS 1289:1986. with a minimum flue cross sectional area of 16500mm2 and a minimum dimension of 90mm. 2.1 The large stove has a rated output in excess of 7Kw and requires a minimum of 11cm2 permanent effective free air. This is in addition to any window that opens, and although it must communicate with the outside air whenver possible, it can communicate with an adjacent room providing such space has a similar opening to the outside. The small and medium stoves have a rated output below 7Kw and do not normally require any additional ventilation. 3.1 Before installation, ensure the local distribution conditions (identification of the type of gas and pressure) and the adjustment of the appliance are compatible. 3.2 Ensure that the gas supply is capable of delivering the required amount of gas, and is in accordance with the rules in force. 3.3 Soft copper tubing and soft soldered joints can be used but must not be closer than 50mm to the base of the tray. 3.4 A means of isolating the gas supply to the appliance must be provided, independent of any appliance control. 3.5 All supply gas pipes must be purged of any debris that may have entered, prior to connection to the appliance. 4.1 This stove must stand on a non-combustible hearth that is ...
Este manual também é adequado para os modelos :Lareiras - 8517-P8517 (603.72 kb)
Lareiras - Clarendon & Ashdon CLARENDON 8541-P8541 (603.72 kb)
Lareiras - 8518-P8518 (603.72 kb)
Lareiras - 8519-P8519 (603.72 kb)