Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
5. When satisfied that the burner flame appearance is normal, close the lower control compartment door then proceed to finish the installation. Air Shutter Adjusting Rod Air Shutter Burner Opening Venturi Tube Opening In This Direction Air Shutter Adjusting Decrease Shutter Arms Ref. Air shutter Patent: Opening In This Direction U.S. Pat. 5,553,603 Note - Both air shutters open and close simultaneously when the air shutter adjusting rod is moved. Orifice Increase Shutter Note - Burners are omitted in this view for clarity. Figure 56 -Burner Air Shutter Adjustment ***Main Burner Factory Air Shutter Opening Setting - All Models Natural Gas inches (millimeters) Propane Gas inches (millimeters) * TWO 1/8 (3) Slots ** TWO 11/16 (17) Slots Adjustment Rod Positions, viewed from above: * Natural Gas - fully clockwise ** Propane- fully counter clockwise ***Settings are shown for each burner. Combustible Finished Wall Materials Top of Appliance Combustible material may touch appliance top Louvers Top of Door Frame Hood must be installed as shown. 3" (76 mm) This Area Must Remain Clear of Combustible Materials 1 in. Min. (25 mm) Drywall Bracket/Spacer Top Spacers Figure 58 -Combustible Wall Framing Header Figure 57 -Burner Flame Appearance Step 11. HOOD INSTALLATION All of these appliances must have hoods installed prior to operating (see Figure 58). Slide the hood into the slots on the lower edge of the cabinet top (see Figure 58). FINISHING REQUIREMENTS Wall Details Complete finished interior wall. To install the appliance facing flush with the finished wall, position framework to accommodate the thickness of the finished wall (Figure 58). See Page 5 for Cold Climate Insulation and Page 8 for Clearances. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Step 12. ATTACHING SAFETY-IN-OPERATION WARNINGS Step 12. ATTACHING SAFETY-IN-OPERATION WARNINGS ATTACHING SAFETY-IN-OPERATION WARNINGS Your fireplace has been furnished with safety instruction labels that are to be affixed to the operation and control point of the fireplace. A safety instruction label should be affixed to the wall switch plate where the fireplace is turned on and off (See Figure A) or wall thermostat (See Figure B) and if used on the remote control handheld transmitter (Figure C). The warnings should already have been put in place when the fireplace initial set-up was completed. If they are not affixed at these spots, locate the multi-lingual adhesive labels provided with these instructions and proceed as follows: 1. Locate the wall switch or wall thermostat that controls the fireplace (verify the switch operates the fireplace by turning it on and off). Clean the wall switch plate or wall thermostat thoroughly to remove any dust and oils. Affix the label to the surface of the plate of the wall switch that controls the fireplace (Figure A) or the wall thermostat (Figure B). Choose the language primarily spoken in the home. 2. Ifaremotecontrolisusedtocontrolthefireplace, locate the transmitter and clean it thoroughly to remove any dust and oils. Affix the label to the surface of handheld transmitter (Figure C). Choose the language primarily spoken in the home. 3. If you are unable to locate the labels, please call Lennox Hearth Products or your nearest Lennox Hearth Products dealer to receive additional safety instruction labels free of charge. Cat. No. H8024 Replacement Label Kit LENNOX HEARTH PRODUCTS 1-800-9-LENNOX Note: English is red text on clear label. French and Spanish are white text on black label. SAFETY LABEL DIAGRAMS APPOSITION DES MISES EN GARDE RELATIVES a LA SeCURITe D’UTILISATION Votrefoyeraetelivreavecdesetiquettesdesecuritequi doivent etre collees a cote des dispositifs de controle du foyer. Une etiquette de securite doit etre collee sur la plaque de l’interrupteur controlant l’allumage du foyer (voir Figure A) ou sur le thermostat mural (voir Figure B) et, le cas echeant, sur le boitier de la telecommande (Figure C). Les mises en garde auraient du etre collees aumoment del’installation initiale du foyer. Si ce n’est pas le cas, prenez les etiquettes adhesives multilingues fournies avec ces instructions et procedez comme suit: 1. Reperez l’interrupteur ou le thermostat mural qui controle le foyer (verifiez que l’interrupteur controle le fonctionnement du foyer en le faisant basculer de Marche a Arret, et vice-versa). Nettoyez soigneusement la plaque murale de l’interrupteur ou le thermostat mural pour eliminer la poussiere et les traces de graisse ou d’huile. Collez l’etiquette sur la surface de la plaque de l’interrupteur mural qui controle le foyer (Figure A) ou du thermostat mural (Figure B). Choisissez la langue qui est principalement parlee dans la residence du proprietaire. 2. Si une telecommande est utilisee pour controler le foyer, nettoyez la soigneusement pour eliminer la poussiere et les traces de graisse ou d’huile. Collez l’etiquette sur le boitier de la telecommande (Figure C). Choisissez la langue qui est principalement...
Este manual também é adequado para os modelos :Lareiras - MILLIVOLT SDVPF-N-B (4.88 mb)
Lareiras - MILLIVOLT SDVPF-N-B (4.88 mb)
Lareiras - MILLIVOLT SDVPF-N-B (4.88 mb)
Lareiras - MILLIVOLT SDVPF-N-B (4.88 mb)