Log:
Assessments - , GPA: ( )

Instruções de Operação FireplaceXtrordinair, Modelo VFD36FB2DL-1

Fabricante : FireplaceXtrordinair
Arquivo Tamanho: 4.64 mb
Arquivo Nome :

Língua de Ensino: en

O documento está colocado, por favor, espere
O documento está colocado, por favor, espere

Facilidade de uso


THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (LATEST EDITION). A factory installed junction box is located on the lower right side of the firebox. Wiring must be fed to the junction box and attached to the receptacle that is provided. From right side of the firebox, remove the screw securing the junction box assembly. Leave approximately 6” of wire in the junction box for connection. Attach black wire to one side of the receptacle and white wire to opposite side of receptacle. The ground wire should be attached to the green (ground) screw. Install the recepticle into the junction box. Attach cover plate. Attention: If installed, do not damage gas inlet supply line when blower assembly is inserted into firebox. In some cases, removal the gas inlet supply line may be necessary. 3. Determine which type of firebox you have prior to installation. See Figures 26 and 27. Figure 25 REMOVE BOTTOM LOUVER TO INSTALL BLOWER ASSEMBLY Figure 26 REMOVE COVER PLATE TO INSTALL BLOWER ASSEMBLY Figure 27 Deluxe Louvered Models Deluxe Flush Face Models 23200-0-1206 Page 13 4. Insert blower assembly into interior, bottom of firebox. Position blower assembly so that you align the notch on back of blower assembly with the center screw on firebox back, then push the blower assembly against firebox back. The blower wheel must be centered with the back wall of the firebox. The magnets on the back and bottom of blower assembly will sufficiently hold blower assembly in place. Note: For field installation of blower assembly, it may be easier to remove rear cover panel to install blower. This eliminates the need to remove brick liner panels, but the blower would have to be installed prior to installing the firebox into a wall or chase. See Figure 28. 5. Once the blower assembly is in position, locate the plug button in the top right rear corner of the firebox. Remove the plug with a standard screwdriver and discard plug. 6. Next, find the fan control switch and wire assembly. Feed the wires through the hole at the top of the firebox, and secure the fan control switch with (2) #6 screws provided. See Figure 29. 7. The fan control wires will slide down between the firebox and outer wrap near the blower assembly. See Figure 29. 8. One fan control wire will have a 1/4” female terminal that must be attached to the open terminal on the blower motor. See Figure 32, Connection A. 9. The other fan control wire has a 1/4” male terminal. Attach this terminal to the open terminal on the blower power cord. See Figure 32, Connection B 10. Route the wires away from moving parts of the blower assembly and retain wires together near the blower motor using the plastic purse clip provided. 11. To complete the installation, plug the power cord into the junction box receptacle at the right rear corner of the firebox outer wrap. See Figure 30. 12. If room permits, the power cord can be located from the o...

Este manual também é adequado para os modelos :
Lareiras - VFD36FB2CL-1 (4.64 mb)
Lareiras - VFD36FB2DF-1 (4.64 mb)
Lareiras - FD42FB2DF-1 (4.64 mb)
Lareiras - VFD32FB0F-1 (4.64 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias