Log:
Assessments - , GPA: ( )

Instruções de Operação Superior, Modelo 36" B-VENTED GAS APPLIANCES B-40RMN

Fabricante : Superior
Arquivo Tamanho: 475.12 kb
Arquivo Nome :

Língua de Ensino: en

O documento está colocado, por favor, espere
O documento está colocado, por favor, espere

Facilidade de uso


(In Canada, the current CSA C22-1 Canadian Electrical Code.) 1. If any of the original wire as supplied must be replaced, it must be replaced with Type AWM 105°C – 18 GA. wire. 2. 120V, 60Hz – Less than 3 amps. BK Junction Box Transf. 120 V. 24 V Factory Wired Field Wired BL Electronic Wiring Diagram (Honeywell) (Optional ON/OFF Switch Wiring) R BK BL To Opposite Side G W OPT. ACCESSORY SWITCH 120 VAC. BK LIMIT SWITCH W Gas Valve B OPTIONAL ON/OFF SWITCH OR WALL SWITCH R IGNITER CONTROL PILOT ASSEMBLY Break Off Tab BK WHT BKBK G G Figure 13 Figure 14 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Step 6. Connecting Gas Line – Make gas line connections. All codes require a shut-off valve mounted in the supply line. Figure 17 illustrates two methods for connecting the gas supply. The flex-line method is acceptable in the U.S., however, Canadian requirements vary depending on locality. Installation must be in compliance with local codes. The gas control valve is located in the lower control compartment. To access the valve remove the removable access panel and set aside (Figure 15). Note:To provide increased access to the lower control compartment, you may choose to remove the front log. To do so, undo the twists in the wires securing the log from below to each of the grate tines. After removal of the log cut the wires off closely to the log before reinstalling it. These are only required for shipping. The millivolt control valve has a ... " (10 mm) NPT thread inlet port. The electronic control valve has a ..." (13 mm) NPT thread inlet port and is fitted with a ..." x ..." (13 mm x 10 mm) NPT fitting. Both the millivolt and electronic models are fitted with a gas flex line and shutoff valve, ..." NPT. Plan the connections accordingly. Gas Controls on Valve SIT Valve Shown Removable Access Panel Figure 15 Secure all joints tightly using appropriate tools and sealing compounds (ensure propane resistant compounds are used in propane applications). Turn on gas supply and test for gas leaks using a soapy water solution. Never use an open flame to check for leaks. A. Mix a 50% dish soap, 50% water solution. B. Light the appliance (refer to the lighting instructions provided in the Homeowner's Care and Operation Instructions). C. Brush all joints and connections with the soapy water solution to check for leaks. If bubbles are formed, or gas odor is detected, turn the gas control knob to the “OFF” position. Either tighten or refasten the leaking connection and retest as described above. Note:Supply wires may be alternatively connected to the outlet using the screw terminals, however the black supply wire must be wired to a terminal that is opposite (across the outlet) the point where the white supply wire is connected. White (Supply) Black (Supply) Bipolar Terminal Screw 120 Vac 60 Hz Ground Wire Connection D. When the gas lines are tested and leak free, observe the individual tongues of flame on the burner. Make sure all ports are open and producing flame evenly across the burner. If any ports are blocked, or partially blocked, clean out the ports. Step 7. Installing Outside Air Kit – These appliances are equipped with an outside (make-up) air door and integral actuator arm. If the appliance is to be installed with an outside air vent system, use only FireCraft Models FAOK-4 or FAOK-4LD Combustion Air Kits. After completing the installation of the optional combustion air vent system the actuator arm must be put in service and tested to ensure proper operation before completing any enclosure around the firebox. Failure to do so may result in extensive and costly rework. WARNING: DO NOT REMOVE THE ACTUATOR ARM LOCKING SCREW UNLESS THE COMPLETE OUTSIDE AIR VENT SYSTEM HAS BEEN INSTALLED IN ACCORDANCE WITH THE DETAILED INSTRUCTIONS PROVIDED WITH THE KIT. Figure 16 . ." Nipple Gas Stub . ." x . ." Flare Shut-Off Valve . ." Flex Tubing . ." NPT Flare Fitting (Remove Before Hard Piping) . ." Union . ." Close Nipple . ." Shut-Off Valve Alternate “Hard Piping” (Millivolt or Electronic) (may be required in some areas, consult local codes.) Figure 17 Gas Flex Line (provided) . ." x . ." Reducer Note: . ." NPT At Inlet Of Gas Valve For Electronic Models. Gas Valve NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Locate the actuator arm along the right side of the appliance firebox opening and refer to Figure 18. After completing the installation of the Outside Combustion Air Kit remove and discard the actuator arm locking screw. Remove Locking Screwand “Pop” Actuator to theLeft Before Initial Use Outside Air Actuator Pull Forward to Open, Push Back to Close Figure 18 To operate, push the end of the actuator to the left as shown in Figure 18, until it "pops" free of its "locked" position. Pull the actuator forward to open the combustion air door, and push it back to close. To "lock" the combustion air door closed, ensure the actuator is pushed all the way back then push the end of the actuators to the right until the step in the actuat...

Este manual também é adequado para os modelos :
Lareiras - 36" B-VENTED GAS APPLIANCES B-40REN (475.12 kb)
Lareiras - 36" B-VENTED GAS APPLIANCES B-40REP (475.12 kb)
Lareiras - 36" B-VENTED GAS APPLIANCES B-40RMP (475.12 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias