Assessments - 1, GPA: 3 ( )

Fabricante : Dell Arquivo Tamanho: 855.98 kb Arquivo Nome : Língua de Ensino:

And when the routing information is set to the target network interface, it will be removed together. You must have platadm privileges to run this command. Refer to setprivileges(8) for more information. System Administration 215 setnetwork(8) OPTIONS OPERANDS The following options are supported: -c {up I down} Specifies whether to enable the specified network interface. One of the following values can be specified. If none of them is specified, an error occurs. up Enables the network interface. down Disables the network interface. -h Displays usage statement. When used with other options or operands, an error occurs. -m addr Specifies a netmask. The following addr form is accepted: xxx.xxx.xxx.xxx xxx An integer from 0-255. Zero suppression can be used to specify the integer. If the -m option omitted, one of the following netmask values is set depending on the address specified in the address operand: ■ If the address specified is class A (e.g. 20.1.1.1), the netmask value 255.0.0.0 is set. ■ If the address specified is class B (e.g. 136.18.1.1), the netmask value 255.255.0.0 is set. ■ If the address specified is class C (e.g. 200.18.108.1), the netmask value 255.255.255.0 is set. -n Automatically answers "n" (no) to all prompts. -q Suppresses all messages to stdout, including prompts. -r Removes the IP address and netmask of the network interface. -y Automatically answers "y" (yes) to all prompts. The following operands are supported: address Specifies an IP address. The specified value is a set of four integer values delimited by the ". " (period). The following address form is accepted: xxx.xxx.xxx.xxx xxx An integer from 0-255. Zero suppression can be used to specify the integer. Specifying the loopback address (127.0.0.0/8), the network address, or a broadcast address, it results in errors. 216 SPARC Enterprise Mx000 Servers XSCF Reference Manual • Last Revised August 2009 setnetwork(8) EXTENDED DESCRIPTION interface Specifies the network interface to be configured. One of the following values can be specified: ■ In the M3000/M4000/M5000 servers: For XSCF unit 0: xscf#0-lan#0 XSCF-LAN#0 xscf#0-lan#1 XSCF-LAN#1 For abbreviation: lan#0 an abbreviation of XSCF-LAN#0 lan#1 an abbreviation of XSCF-LAN#1 ■ In the M8000/M9000 servers: Specifying the -c or -r option and Inter SCF Network (ISN) together, it results in errors. For XSCF unit 0: xscf#0-lan#0 XSCF-LAN#0 xscf#0-lan#1 XSCF-LAN#1 xscf#0-if ISN For XSCF unit 1 : xscf#1-lan#0 xscf#1-lan#1 xscf#1-if XSCF-LAN#0 XSCF-LAN#1 ISN For takeover IP address: lan#0 takeover IP address for XSCF-LAN#0 lan#1 takeover IP address for XSCF-LAN#1 ■ In the M8000/M9000 servers, a takeover IP address can be used without a need to determine whether XSCF has been switched. By setting the LAN ports of the active XSCF unit as lan#0 and lan#1, they can be accessed with the names lan#0 and lan#1. ■ In the M3000/M4000/M5000 servers, the value of the lan#0 is fixed with xscf#0-lan#0, and the lan#1 is fixed with xscf#0-lan#1. System Administration 217 setnetwork(8) EXAMPLES ■ After you set the network interface, if you disable that network interface and execute the applynetwork(8) command, the setting data of IP address and netmask will be stored in XSCF. When you enable the network interface, the setting of IP address and netmask will be used. ■ In the following cases, the setnetwork(8) command results in an error: ■ When specified the same subnet in XSCF-LAN#0 and XSCF-LAN#1 ■ When specified the same IP address as DSCP ■ When specified a subnet which overlaps with DSCP ■ When specified the overlapped subnets in ISN and in other network interface ■ When specified the -c or -r option and ISN together ■ In case you specified the IP address and the netmask to the interfaces other than ISN and when the ISN is not configured, the following default value will be set: ■ xscf#0-if: IP address: 192.168.1.1 Netmask: 255.255.255.0 ■ xscf#1-if: IP address: 192.168.1.2 Netmask: 255.255.255.0 ■ The shownetwork(8) command can display current information on a network interface configured for XSCF. ■ To reflect information on the specified network interface, execute the applynetwork(8) command and reset XSCF. EXAMPLE 1 Sets the IP address 192.168.10.10 and netmask 255.255.255.0 for XSCF-LAN#0 on XSCF unit 0. xscf> setnetwork xscf#0-lan#0 -m 255.255.255.0 192.168.10.10 EXAMPLE 2 Sets the IP address 192.168.10.10 and netmask 255.255.255.0 for XSCF-LAN#0 on XSCF unit 0 in the M3000/M4000/M5000 server. xscf> setnetwork lan#0 -m 255.255.255.0 192.168.10.10 example 3 Disables XSCF-LAN#1 on XSCF unit 0. xscf> setnetwork xscf#0-lan#1 -c down EXAMPLE 4 Sets the IP address 192.168.10.128 on ISN on the XSCF unit 0. By default, 255.255.255.0 is set for the netmask. xscf> setnetwork xscf#0-if 192.168.10.128 EXAMPLE 5 Sets the IP address 192.168.11.10 and netmask 255.255.255.0 for XSCF-LAN#0 218 SPARC Enterprise Mx000 Servers XSCF ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :