Assessments - 3, GPA: 4 ( )

Fabricante : Dell Arquivo Tamanho: 17.3 mb Arquivo Nome : Língua de Ensino:

3 Pry the ends of the blank outward until the blank is free. For 2.5-inch hard drive configurations, remove the blank as you would the 2.5-inch hard drive carrier: 1 Remove the front bezel, if attached. See "Removing the Front Bezel" on page 53. 2 Open the drive blank release handle to release the blank. See Figure 3-4. 3 Slide the drive blank out until it is free of the drive bay. Installing System Components Installing a Drive Blank The process for installing a drive blank depends on whether your system is configured with 3.5-inch or 2.5-inch hard drives. For 3.5-inch hard drive configurations, the drive blank is keyed to ensure correct insertion into the drive bay. To install a 3.5-inch drive blank, insert and rotate in the keyed side of the blank into the drive bay and press evenly on the other end of the blank until it is fully inserted and latched. For 2.5-inch hard drive configurations, install the hard drive blank as a 2.5-inch hard drive carrier: 1 Remove the front bezel, if attached. See "Removing the Front Bezel" on page 53. 2 Open the handle on the drive blank. 3 Insert the drive blank into the drive bay until the blank is fully seated. 4 Close the handle to lock the blank in place. 5 Replace the front bezel, if it was removed in step 1. Removing a Hot-Plug Hard Drive 1 Remove the front bezel, if attached. See "Removing the Front Bezel" on page 53. 2 From the RAID management software, prepare the drive for removal and wait until the hard-drive indicators on the drive carrier signal that the drive can be removed safely. See your SAS RAID controller documentation for information about hot-plug drive removal. If the drive has been online, the green activity/fault indicator will flash as the drive is powered down. When both drive indicators are off, the drive is ready for removal. 3 Open the drive carrier release handle to release the drive. See Figure 3-4. 4 Slide the hard drive out until it is free of the drive bay. 5 If you do not replace the hard drive, insert a drive blank in the vacated drive bay. See "Installing a Drive Blank" on page 57. NOTICE: To maintain proper system cooling, all empty hard-drive bays must have drive blanks installed. Installing a Hot-Plug Hard Drive NOTICE: When installing a hard drive, ensure that the adjacent drives are fully installed. Inserting a hard-drive carrier and attempting to lock its handle next to a partially installed carrier can damage the partially installed carrier's shield spring and make it unusable. NOTICE: Not all operating systems support hot-plug drive installation. See the documentation supplied with your operating system. 1 Remove the front bezel, if attached. See "Removing the Front Bezel" on page 53. 2 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank" on page 56. 3 Install the hot-plug hard drive. a Open the handle on the hard-drive carrier. Installing System Components 58 Installing System Components Figure 3-4. Installing a Hot-Plug Hard Drive b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane. c Close the handle to lock the drive in place. 4 Replace the front bezel, if it was removed in step 1. Replacing a Hard-Drive Carrier Removing a Hard Drive From a Hard-Drive Carrier 1 If you are removing a SATA hard drive from a SATAu drive carrier, remove the interposer card: a Viewing the hard drive carrier from the rear, locate the release lever on the left end of the interposer card. b Push the lever away from the carrier rail to release the left end of the card. c Rotate the left end away from the hard drive to release the connector. d Pull the right end of the interposer card clear of the slots in the carrier rail. 2 Remove the four screws from the slide rails on the hard-drive carrier and separate the hard drive from the carrier. 1 hard drive 2 drive carrier 3 drive carrier release handle 3 1 2 Installing a SAS Hard Drive Into a SATAu Drive Carrier NOTE: SAS hard drives must be installed only in SATAu drive carriers. The SATAu drive carrier is labeled "SATAu" and also has marks indicating the SAS and SATA mounting screws. 1 Insert the SAS hard drive into the hard-drive carrier with the connector end of the drive at the rear. See Figure 3-5. 2 Viewing the assembly as shown in Figure 3-5, align the bottom rear screw hole on the hard drive with the hole labeled "SAS" on the hard drive carrier. When aligned correctly, the rear of the hard drive will be flush with the rear of the hard-drive carrier. 3 Attach the four screws to secure the hard drive to the hard-drive carrier. See Figure 3-5. Figure 3-5. Installing a SAS Hard Drive Into a SATAu Drive Carrier SATAuSAS1 3 2 1 screws (4) 2 SATAu drive carrier 3 SAS hard drive Installing System Components 60 Installing System Components Installing a SATA Hard Drive Into a SATA Drive Carrier NOTE: SATA hard drives that connect directly to the SAS backplane must be installed in SATA drive carriers (labeled "SATA"). Only SATA hard drives ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :