Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Carefully reassemble the plastic RING GUARD COVER by putting it in position using the three guide PINS (Fig. 14). Carefully reassemble the TOP KNIFE COVER (Fig. 13) by putting it in position over the plastic RING GUARD COVER using the three guide PINS. Secure both RING GUARD COVER and TOP KNIFE COVER by turning the LATCH KNOB (Fig. 7) counterclockwise while lowering the TOP KNIFE COVER; then release the LATCH KNOB and turn it clockwise until snug. Reassemble the SHARPENER by lowering it straight down so the ROD AND PIN fit the SLOT on the SHARPENER MOUNT (Fig. 12). Replace the DEFLECTOR, if present, below the KNIFE (Fig. 16); also, refer to page 3. To reinstall the PRODUCT TRAY, hold it with both hands and lower it so the bottom of the SUPPORT ARM fits on the CARRIAGE HINGE PINS (Fig. 17). Return the PRODUCT TRAY to the GAUGE PLATE by tilting the PRODUCT TRAY to the left. Turn the KNOB on the SUPPORT ARM in either direction until it moves inward, then turn the KNOB clockwise until snug. The LIFT ASSIST (Fig. 18) underneath the machine, allows you to lift the right side of the slicer base with little effort — the slicer is completely supported so you can clean underneath. Press down on the right side of the slicer to lower it back to the table. KNIFE Fig. 15 PAPER TOWEL RING GUARD GAUGE PLATE DEFLECTOR BRACKET KNIFE SHARPENER MOUNT DEFLECTOR Fig. 16 NOTE: Failure to follow use, care, and maintenance instructions may void your Hobart warranty. SUPPORT ARM CARRIAGE BOTTOM OF SUPPORT ARM KNOB LIFT ASSIST HINGE PIN Fig. 17 Fig. 18 – 9 – KNIFE REMOVAL TOOL PIN IN HOLE @ 11 O’CLOCK KNIFE REMOVAL TOOL PIN IN HOLE @ 11 O’CLOCK Unplug the machine power cord and turn the index knob fully clockwise to close the gauge plate before cleaning the slicer. To Remove the Knife . . . • Remove the TOP KNIFE COVER and the plastic RING GUARD COVER (Figs. 13, 14). Remove the plastic cover from the KNIFE NUT. Orient the Knife . . . • Rotate the KNIFE using your hand on the back of the Fig. 19 RIDGE ON KNIFE HUB (PLASTIC COVER REMOVED) PIN @ 1 O’CLOCK HOLE @ 11 O’CLOCK knife, the RIDGE on the KNIFE HUB must align with the PIN on the RING GUARD at the 1 o'clock position (Fig. 19). • Arrows on the KNIFE point to the three PINS on the RING SLOTS GUARD. AROUND 3 PINS Attach the Knife Removal Tool . . . • Place the KNIFE REMOVAL TOOL on the KNIFE. The three slots on the TOOL fit the three PINS ON THE RING GUARD (Fig. 20). The PIN on the KNIFE REMOVAL TOOL fits the hole in the KNIFE at the 11 o'clock position (Fig. 21). • First, push the HANDLE firmly, all the way into the hub. Then, turn the HANDLE counterclockwise until it stops (Fig. 22). You may experience resistance when turning. • Lift KNIFE and TOOL up and out (Fig. 23). Fig. 20 PIN @ 11 HANDLE O’CLOCK Fig. 21Fig. 22 •Wash, rinse and sanitize the KNIFE and KNIFE REMOVAL TOOL in a sink or dishwasher. •Wash, rinse and sanitize the slicer base (Fig. 24). Fig. 23 PIN Fig. 24 KNIFE REMOVED KNIFE NUT RING GUARD KNIFE HUB RIDGE – 10 – To Reinstall the Knife . . . • Orient the RIDGE on the KNIFE HUB so it points to the PIN on the RING GUARD at the 1 o'clock position (Fig. 24). • Place the KNIFE and TOOL so the PIN on the KNIFE REMOVAL TOOL is at the 11 o'clock position (Fig. 23). The SLOTS on the KNIFE REMOVAL TOOL fit around the three PINS on the RING GUARD (FIG. 20). • If the TOOL does not push the pins on the back of the KNIFE into the HUB (Fig. 25), slightly nudge the HANDLE upwards (Fig. 26) to lock the pins into the KNIFE NUT. • First, push the HANDLE firmly, all the way into the HUB to engage the pins. Then, turn the HANDLE clockwise until it stops (Fig. 27). You may experience resistance when turning. • The KNIFE is reattached. Lift the TOOL up and out. • Replace the plastic cover on the KNIFE NUT. Reassemble Slicer Parts • Place the plastic RING GUARD COVER on the RING GUARD, align using the three guide PINS (Fig. 14). • Place the TOP KNIFE COVER on top of the RING GUARD COVER, aligning with the three guide PINS (Fig. 13). Secure the RING GUARD COVER and the TOP KNIFE COVER by turning the LATCH KNOB (Fig. 7) counterclockwise while lowering the TOP KNIFE COVER; then, release the LATCH KNOB and turn it clockwise until snug. • Lower the SHARPENER so the ROD AND Fig. 25 Fig. 26 Fig. 27 PIN, underneath, fit the SLOT in the SHARPENER MOUNT (Fig. 12). • Reinstall the PRODUCT TRAY by holding it with both hands and lowering the bottom of the SUPPORT ARM so it fits on the CARRIAGE HINGE PINS (Fig. 17). • Return the PRODUCT TRAY to the GAUGE PLATE by tilting it to the left. Turn the KNOB on the SUPPORT ARM loosely in either direction until it moves inward, then turn it clockwise until snug (Fig. 28). To reattach accessories — refer to page 3. SHARPENER KNIFE COVER KNOB PRODUCT TRAY SUPPORT ARM Fig. 28 – 11 – MAINTENANCE Unplug the machine power cord and turn the index knob fully clockwise to close the gauge plate before doing any maintenance on the slicer. KNIFE SHARPENING The CleanCutTM KNI...
Este manual também é adequado para os modelos :Panelas - ML-136145 (1.15 mb)