Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
6. Displayes the direction of the rollers. 7. Shows cold function. 175 Mic=7 mil, 250 Mic=10 mil 8 3. BUTTON FUNCTIONS : Check current temperature : Hot/Cold function : Working condition and T-CheckMEMORYHOT/COLDT-CheckMEMORYHOT/COLD Cold function cancel : Increase temperature : Decrease temperature : Increase speed : Decrease speed : Restore the memorized working setting : Restore the memorized working setting : Reverse function : Power On/Off 9 4. HOW TO SET THE BUTTONS (Buzzer rings each time you press the button.) 1.Temperature available range from 20. to 160.. 2.Each time you press or to set temperature, it will change 1.(1.) at a time. If you press the button for more than 2 seconds, temperature will change automatically. 1.You can use 7 different lamination speed. 2.You can change speed with or 1. Press button when check the current temperature. 2. The current temperature will blink on the display for a second and turns back to the setting mode. ***SET TEMPERATURE*** ***SPEED CONTROLS*** ***CHECK TEMPERATURE ON THE ROLLER *** T-Check T-Check 10 1) Memorizing working condition 1. The laminator can memorize up to 6 settings. 2. Use up and down arrows to set or 3. When you complete the optimum laminating conditions (Speed & Temperature), button. This setting is memorized and confirmed when the light blinks. 4. To enter other settings into memory, repeat steps 2 and 3. 2) Using the memorized settings 1. You can choose any one of 6 settings in memory. 2. Use the up and down arrows to select or a setting form memory. 1. Press button. It will show a on the display. 2. The speed will always be shown "2" and there is no memory setting this function. 3. Speed can be varied 0 to 7 by selecting or button 4. You can release the machine from cold mode by pressing ***COLD MODE*** ***MEMORIZING WORKING CONDITION AND USING THE MEMORIZED WORKING CONDITION*** MEMORY MEMORY HOT/COLD HOT/COLD HOT/COLD 11 1. HOT LAMINATING 1. Press the power button. 2. Please refer Information Panel on the front of product. 3. Select a memory setting by pressing the and button. 4. It is ready when the LCD window shows and the buzzer rings three times. 5. After Insert document or photograph to be laminated into a laminating pouch, insert pouch squarely into opening slot. 6. Finished laminated pouch will exit through rear of machine. 7. Emerging laminated document is hot to touch. Please handle it to be cooled down. (If document is not laminated well, do lamination again.) 8. When the machine is on for an extended period of time, use a slightly lower temperature setting as the internal temperature of the machine may actually be higher than the preset temperature, which may cause the document may ripple or bend. 9. When you are finished laminating, press the power button to turn off. * When continuously laminating, the ready signal ( ) may disappear and the waiting signal may be displayed on LCD window. At this time, if pouch is being laminated, finish laminating and then laminate new one after is showed. * Do not laminate empty or thin pouch on a thick film setting. The pouch could stick to the roller. * Do not unplug laminator while laminating. This could be fatal for the rollers due to the high internal temperature. LAMINATING STEPS ***USEFUL INFORMATION*** 12 2. COLD LAMINATING 1. Press the power button to turn on. 2. Press 3. It is ready when LCD window shows and the buzzor rings three times. 4. Insert document into a Royal Sovereign cold laminating pouch as follows. 1) Prepare cold pouch film. 2) Remove protective paper inside cold pouch. (Be careful not to allow the pouch to close and seal itself closed. If the pouch closes on itself and seals,you will not be able to the document to be laminated inside.) 3) Place document squarely into the pouch, where the protecting paper was. Cold film's minimum border of about 3mm(1/8") is necessary to provide a proper edge seal. 4) Beware of dust while inserting document. 5) Feed pouch squarely into opening slot. 5. Finished laminated pouch will exit through rear of machine. 6. When you are finished laminating, press the power button to turn off. If it has recently been used for hot lamination, allow the rollers to be cooled down about 20~30 minutes. **HOW TO ATTACH DOCUMENT ON COLD POUCH FILM** ***USEFUL INFORMATION*** Front Back Back HOT/COLD 13 3. COLOR FOIL LAMINATING **Your laminator has ability to add color by applying color foil to documents copied or printed by lasor printer or toner copier.** **PAPER CARRIER is required** 1. Press the power button to turn the laminator on. 2. Find FOIL FUNCTION using the up arrow. 3. It is ready when LCD window shows and the buzzer rings 3 times. 4. Position the color foil on document and put it in paper carrier. 5. Feed paper carrier squarely into opening slot. 6. Finished laminated paper will exit through rear of machine. 7. When you are finished laminating, press the power button to turn off. * The document, which has been foil laminated, is pretty hot...
Este manual também é adequado para os modelos :Laminador - 900N 1 (1.03 mb)
Laminador - NPH-1200 (1.03 mb)