Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
To insure high quality lamination, please read this instruction manual thoroughly. For additional product support or factory-direct ordering information, call Royal Sovereign Customer Service at (201)568-0830 or toll free call, (800)397-1025. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating the machine. Keep this information for future reference. Failure to comply with any of the following safety procedures could result in serious personal injuries 1. To prevent the possibility of electrical shock, do not immerse machine in water or permit liquids to get inside. 2. Do not allow articles of clothing (neckties, scarves, etc.) or papers near the front or rear of the machine while operating as they could get cought by the rollers and be pulled inside, causing personal injury. 3. Do not attemp to laminate that exceed total recommended material thickness. 4. Do not operate machine for any other purpose than its intended use. 5. Do not operate machine when electrical plug or power cord is damaged. 6. Turn off the power when not in use. Unplug machine before moving it or when it is not in use for an extended period of time. 7. This machine is indoor use only. 8. Do not alter the electric plug in any use. 3 CHARACTERISTICS OF LAMINATOR NPH-1200N/900N This machine has been designed using the latest laminating technology. 1. This machine is controlled by a state-of-the-art Microprocessor. a) Protect the rollers--When the power is off or a power failure occurs, rollers continue to turn until the unit properly cools down. b) Automatic overheating protection--If a temperature sensor should fail, the heating elements will not heat up. c) You can set your own operating conditions into "Memory". 2. Temperature and speed can be adjusted, to properly laminate various film thickness. 3. A buzzer rings, alerting you that a butten has been pressed. This prevents accidental setting changes. 4. Roller cover may be opened for easy access to clean the rollers. 5. Thermostats are used to economically maintain consistent temperature. 4 SPECIFICATIONS Description NPH - 1200N NPH - 900N Dimensions(w x d x h) 580x290x135mm (22.8"x11.4"x5.3") 505x290x135mm (19.9"x11.4"x5.3") Max.Laminating Width 330mm (13") 240mm (9.4") Max.Lam. Thickness 2mm (1/12") Film Thickness 75 ~ 250mic (3 ~ 10 mil) Transport Type Four Roller (no carrier) Heat Source Hot Roller Type Pre-Heating Time 4 ~ 5 min Temp. Operating Range 20 ~ 160. Cooling Fan Type DC FAN Motor Type DC GEARED MOTOR Max. Laminating Speed 750mm/min (29.5" per min) Weight 11Kg (24 lbs) 9Kg (20 lbs) Voltage / Cycle AC 120V/60Hz (AC230~240V ,50/60Hz) Power Consumption 1000W 850W SETUP Place laminator on a sturdy, flat work surface. Allow ample clearence behind laminator for laminated document or photograph to exit completely without bending. Connect laminator to an electrical outlet that matches laminator's rated voltage and power requirements. If an extension cord is required, use a cord rated higher than the laminator's capacity. 5 1. Top Cabinet 2. Roller Cover 3. Roller Cover Screws 4. Control Panel 5. LCD Window 6. Input 7. Output 8. Power Cord MAJOR PARTS IDENTIFICATION 6 Appropriate speed and temperature may be set, using the LCD controller. The LCD panel was designed for convenience, by incorporating the ability to program your settings into "Memory". 1. CONTROL PANEL SETTINGS LCD DISPLAY BUTTONS CONTROL PANEL INSTRUCTIONS T-Check COLD MEMORY HOT/COLD 7 2. LCD WINDOW 1. * 6 film thickness options 75 Mic=3 mil, 100 Mic=4 mil, 125 Mic=5 mil 2. SPEED * 7 speed options Setting 1 is slowest / Setting 7 is fastest 3. TEMPERATURE Display the present temperature. 4. Is displayed when the present temperature is reached. 5. Indicates to wait till blinking stops. Current temperature is higher or lower than the preset temperature. 6. Displayes the direction of the rollers. 7. Shows cold function. 175 Mic=7 mil, 250 Mic=10 mil 8 3. BUTTON FUNCTIONS : Check current temperature : Hot/Cold function : Working condition and T-CheckMEMORYHOT/COLDT-CheckMEMORYHOT/COLD Cold function cancel : Increase temperature : Decrease temperature : Increase speed : Decrease speed : Restore the memorized working setting : Restore the memorized working setting : Reverse function : Power On/Off 9 ...
Este manual também é adequado para os modelos :Laminador - 900NPH-1200N (1.03 mb)
Laminador - NPH-1200 (1.03 mb)